I am doing the research work in sheet metal forming (deep drawing). So please anyone help me to do the deep drawing process in ANSYS software.If you have any tutorial please send it to my e-mail-id:[email protected]
Thanking you,
by
M.Subramanian
You can do it in ANSYS. But it is better to do in Abaqus. You will get tutorial on it in Abaqus.
https://www.youtube.com/watch?v=2cK8Yb6Gx5o
In ANSYS also you can do it using ANSYS/LS-DYNA module.
I want to do the warm deep drawing using Abaqus software. Since I have some idea about the cold deep drawing for simulation.If anybody have idea related to the warm deep drawing please share with...
11 December 2016 3,531 0 View
I have seen ductile fracture criterion(Frendenthal ,ckcroft and Latham ,Brozzo ,Ohet al) in some journals.I could not able to understand how to calculate material constants (c).If anybody have...
11 December 2016 5,671 2 View
I have seen some journals in that the ductile fracture criterion (Frendenthal ,cockcroft and Latham ,Brozzo ,Ohet al)were used. I could not understand how the material constants (c) determined. If...
11 December 2016 1,808 3 View
I am doing my research work in micro deep drawing ,I want to know the Voronoi cell FEM and how to implement the concept in Abaqus software for finding the size effect. Thank you, M.Subramanian
06 July 2016 3,847 2 View
I have sent a research paper to a journal. In that paper ,I selected the punch diameter of 5 mm. The reviewer comment is as follows: "The punch diameter of the forming parts in this paper is 5mm,...
05 June 2016 6,773 0 View
Can anyone give ideas or tutorial for warm deep drawing process by using Abaqus software.How to give the temperature and heat transfer co-efficient in the software. With regards, M.Subramanian
05 June 2016 4,314 1 View
I am using the software Abaqus for micro deep drawing , I sent my paper to the journal for publication, but I received the comment from reviewer is " FEM simulation is not suitable for micro deep...
05 June 2016 3,079 5 View
I have simulated 2D deep drawing process using Abaqus software. I got the result for deformed cup output.In the output contour result, the maximum value of PEEQ is indicated in the Die corner...
07 August 2015 5,423 4 View
I have some idea about the 2D simulation of deep drawing by referring the Abaqus user's manual.Since I want to simulate the 2D or 3D simulation of deep drawing in warm conditions.If anybody have...
05 June 2015 4,499 0 View
I have done the 3D deep drawing process simulation in Abaqus software.I modelled and applied boundary conditions. When I try to submit the file for analysis, I have received the error message. I...
03 April 2015 7,793 3 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
Hello Everyone! I am trying to create a metal hydride system where I am trying to create a temperature control with the emphasis on measuring the concentration of the hydrogen with the hydrogen...
29 July 2024 7,577 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Understand how to utilize biosynthesis to develop natural and sustainable solutions to address heavy metal pollution and improve environmental and agricultural conditions.
26 July 2024 1,469 1 View
I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose
25 July 2024 438 3 View
I intend to get an economical and accurate LAB TEST to measure arsenic concentration in blood sample.
23 July 2024 3,654 2 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View
Can the mode volume in smaller metal nanoparticles be larger than the nanoparticle volume?
18 July 2024 4,859 4 View