Why do my MCFs not form monolayer?

Hello, I am looking for some expertise on culturing MCF7s. I purchased them from ATCC and I have been following all media and culture conditions. Media is EMEM with 10% FBS and 10ug/mL of...

27 February 2021 3,904 2 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

Can we measure porosity of a composite by DSC (heat flow measurements)?

In the DSC conducted for A and B (image provided). B is a derivative of A. Can I conclude that the porosity of composite B is more than A, Since the heat flow is decreasing with increase in...

26 December 2020 9,104 3 View

Can I carry out LC-MS for AuNPs?

Will it be helpful to know the nature of stabilizers used in synthesis of curcumin (if it has polymerized or not). Any specific measures to be followed to carry out these kind of experiments?

15 December 2020 2,283 4 View

For lc50 study on fish against bacteria, the test performed referring to OD reading at 625nm. Is it acceptable method?

I would like to clarify regarding a method used to perform LC50 to infect fish by a particular bacteria strain. I prepared an overnight bacteria culture, collect the pellet from overnight culture...

05 December 2020 7,220 1 View

Why I am not getting UV absorbance peak of AuNPs?

I synthesized Au deposited on graphite electrochemically by using chronopotentiometry. How much ever I tried I couldn't get UV absorbance peak of AuNPs in any number of solutions I tried? But when...

20 October 2020 2,040 5 View

Can i use surfactant C-TAB in extraction and detection of the aminaphthalene sulfonates by HPLC technique?

In the detection of Aminonaphthalene sulfonates the quaternary ammonium salts like Tetrabutyl ammonium bromide ,Triethyl ammonium acetates are used so the C-TAB being an quarternary ammonium...

21 September 2020 9,636 1 View

How to fill the gap between two contigs?

Hi everyone, We have sequenced genome of data of a comparatively less studied species using Pacbio long read sequencer. Now after initial assembly we compared the contigs with previous version...

25 June 2020 3,442 3 View

Which motion analysis software can give me this functionality to create some sort of kinematic model?

25 October 2019 2,556 6 View

Automation in ansys with load location as parameter?

What is the best way (in a way that ansys runs each job sequentially without manual command) to solve several problems (say 1000+) with exact same geometry and other solution parameters but...

07 October 2019 2,073 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Precipitate after adding laemmli buffer to protein solution containing Potassium Acetate?

Hi, I am running a size exclusion chromatography experiment with a buffer containing Potassium Acetate as a salt. I analyse these fractions through SDS-PAGE. After boiling my SEC fractions in...

01 March 2021 2,622 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

RIA. How to measure?

When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...

28 February 2021 2,133 3 View

What is the most suitable resuspension buffer for TCA/acetone precipitated protein?

I need to extract protein from fermented carbon sources for Bradford assay. Most researchers experiencing insolubility of pellet in resuspension buffer. Please assist me to select most suitable...

26 February 2021 7,129 3 View

EMSA troubleshooting. Protein-DNA complex not migrating, cold probe lane with multiple bands. Can anyone help?

I'm running an EMSA to show the DNA binding activity of recombinant proteins versus the Wild type. Previous assays run by my research group using a different test system show the protein-DNA...

24 February 2021 8,325 1 View

Can two EC50 values with different hill slopes be compared?

Hello, I fit a classical dose response curve Y=Bottom + (Top-Bottom)/(1+10^((LogEC-X)*HillSlope)) to my data (not related to inhibitors etc). The model I use is purely qualitative but it fits...

23 February 2021 8,155 5 View

No title

22 February 2021 9,932 11 View

Is there a method for evaluating nanoparticle adhesion to epithelial tissue in vitro?

I want to measure how well nanoparticles can transfect cells based on NP adhesion properties. In the literature I find people do it in animal studies, and epithelial adhesion helps in transfection...

21 February 2021 7,791 3 View

How to select therorical or conceptual framework for any proposed qualitative research work?

Hi, I am conducting an exploratory research with qualitative in-depth interview approach to understand the impact of COVID_19 in health systems response to burn care in India. Since, this is a...

19 February 2021 4,562 4 View