I did SEM test by a laboratory. He send the report to me. I am not able to understand how to study that report. Kindly suggest me any information regarding that
Is there any standard procedure or method to determine the bond strength between steel and concrete?
08 September 2018 5,992 4 View
New trends in concreting with alternative binders instead of cement.
07 August 2018 6,630 19 View
I want to examine the performance of a column under eccentric compressive load, the stiffeners have to provide at both ends of specimen to avoid local failure, the specimen will be examined with...
08 September 2017 8,872 2 View
Calcium bentonite is a kind of expansive clay which tends to increase the volume up to 9 % when we add some water to it. As per my knowledge, increase of strength is occurs as a result internal...
09 October 2016 4,381 3 View
Iam going examine the properties blendened concrete by partial replacement of cement with calcium bentonite. The normal consistency of bentonite is much higher than cement. Can any one help me...
09 October 2016 1,181 5 View
These are special concretes which the volume will increase when we add some material to concrete. a lot of research to be done regarding this topic. Sodium polyacrylate is the material I am using...
09 October 2016 6,469 4 View
I am going check deflections and crack widths of a new blended concrete column. I need to compare theoretical values with experimental results to get correlation factor for compression members for...
01 January 1970 1,738 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...
07 August 2024 5,343 2 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...
05 August 2024 9,637 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View