By Modifying the exit geomentry of silencer can we increase the performance of CI engine ?

Manigandan Sekar @Manigandan-Sekar

05 November 2017 0 6K Report

Modifying the exit geometry of silencer from circular to elliptic alters the efficiency ?

Badges
Science topic

More Manigandan Sekar's questions See All

Dear all, Is there any model available to predict the "possible diseases" based on the available pollutant concentration in air ?

In detailed human health risk assessment models. Is there any model that can predict the possible disease.

21 December 2020 7,535 5 View

How to get best LSTM model for regression problem? how to tune or select hyper parameters?

How to get best LSTM model for regression or prediction problem? how to tune or select hyper parameters?

29 June 2020 9,377 4 View

How to work with phasor model in matlab?

I am running IEEE 13 bus model in MATLAB with discrete time . But when I connect Renewable energy DFIG model with IEEE 13 bus system not working due to phase model of DFIG. How to rectify error?

31 January 2020 7,950 4 View

In fluent heat flux analysis results are not converging ?

I had solved the heat flux analysis of the multi-domain problem in fluent. Even after the 20000 iterations also the solution is not converging. As the iterations increase the results are diverging...

05 November 2019 1,713 3 View

Any specific procedure to be followed while converting one dimensional data into image?

Is there any specific procedure to convert 1D data to image before feeding convolutional neural networks ?

18 October 2019 8,309 4 View

Is there any open source Software In Loop (SIL) test method.?

Is there any open-source Software In Loop (SIL) test method available to test the network that was actually created in MATLAB. Anyone guide or give reference to use OPAL-RT testbed to integrate...

06 October 2019 8,124 1 View

Do addition of nanopartilces in soil increases the Plant yield ?

Can any one explain me that addition of nanoparticles enhances the growth of plant and produces more yield. If so, can anyone list me the nanoparticles i can use Plant is Tomato and Aubergines

24 June 2019 5,402 3 View

Do anyone have working protocol for cardiac perfusion in mice?

I am new to perfusion. I need to do cardiac perfusion in mice and my area of interest is brain further to sectioning and IHC. Does anyone have standard protocol of cardiac perfusion for this. Help...

29 May 2019 6,919 3 View

Is addition and removal of Co-author during submission of revised article is acceptable @Elsevier ?

I like to know the removal, addition and shuffling of co-authors is against moral and ethics in Elsevier Journals. Is it necessary to contact a editor to make such changes

20 February 2019 3,676 18 View

How to gelatin coat flasks for primary rat astrocyte culture?? Suggest me with how much percentage gelatin should i use??

I'm gonna culture rat mixed glial cells for first time. suggest me with how much percentage gelatin should i use to culture cells..

07 November 2018 7,023 6 View

Trouble with Charting with Google Earth Engine (Technical)?

Hello. I have a problem with the charting in google earth engine. I created an image collection by combining 5 image collections of five parameters and using ee.Join.inner ( ) and .apply ( )...

26 February 2021 7,084 2 View

How to combine two geometries in LAMMPS ?

I am trying to simulate contact angle of water on a quartz slab using LAMMPS. I have created and equilibriated the quartz slab and the water cluster separately. Now I want to create a composite...

17 February 2021 5,884 2 View

Can I get the design of circular cylinder to fix thermocouple on the surface and cartridge heater in core ?

Respected Scientific Community. I'm interested to carry out experimental studies on a circular cylinder. But even after doing literature review I unable to get the exact design of the cylinder...

10 February 2021 6,221 1 View

Can I use asymmetric PCR amplification on a pool of circular plasmids to increase each plasmid's signal?

Hello, Here is my experiment: I transfect in a plasmid that has been cut once (a linear piece of dsDNA) into human cultured cells. I wait 48hrs to allow the cells to "repair" the plasmid making...

10 February 2021 6,090 3 View

How to mesh complex geometry?

I have been trying to mesh some complex geometry and have been having issues. I have attached images of the geometry in question. This structure is very large in size but has some comparatively...

05 February 2021 6,379 5 View

Please recommend me the proper steps (blocking method) to generate Hexahedral mesh of the following geometry inside ICEM-CFD?

I am facing an issue while blocking for the geometry mentioned in the image. After blocking it ends with a triangular block due to its shape. How to create a hexahedral mesh for this geometry in...

02 February 2021 888 1 View

I want to extract engine oil from a soil sample,please how much amount of anhydrous sodium sulphate am i going to add to 10kg soil?

Engine oil extraction from contaminated soil,10kg of contaminated soil+20ml of dicholoromethane+? of anhydrous sulphate

01 February 2021 9,509 1 View

How to find nature of extremum of a functional? what are the mathematical prerequisites to understand it?

For a function, usually sign of second derivative (and if it is zero, even/odd index of higher order derivative whose numerical value is zero) is enough to detect whether the extreme point is...

25 January 2021 7,703 3 View

Frequency calculation with TDDFT???

Hi, I have been trying to calculate the frequency vibrations of the excited state S1 of an organic molecule (24 atoms). The geometry optimisation of the excited state converged smoothly howerver...

22 January 2021 1,463 3 View

Doubt in DFT geometry preparation?

Hi all, I am trying to perform some ab inito DFT calculations using cp2k code. I have a unit cell of 120 atoms and would like to know how to refine or reduce the number of atoms in the unit cell...

20 January 2021 6,024 3 View