For SPST switches computation of G/S/G for CPW is easy, but what about rotary type SPNT Switches?
I am trying to deposit DC sputtered GeTe thin films. I need to anneal the films to crystallize them. I am using RCA1 cleaned substrates with chamber vacuum > 2e-8 Torr. After deposition, films...
05 June 2017 2,360 8 View
I am trying to design micro-heaters that should go more than 800 deg C. I tried different materials, but tungsten seems a potential candidate. I am using lift-off to pattern the thin films of...
05 June 2017 8,298 4 View
Hi, Can anybody help me in calculating RF MEMS Switching Speeds in Comsol Multiphysics/ANSYS? Can anybody share the sample/example model? I am using Ansys HFSS. Can we do this by exporting the...
08 September 2014 6,759 6 View
I tried few examples to calculate RF MEMS pull-in voltage, but many a times, the solution does not converge. I tried to match with numerical values, but the values are not same. Can anyone share...
08 September 2014 2,628 2 View
I've using Word since so many years, but new to LaTeX, and starting seems difficult as there are a lot of commands. Is LaTeX is really better than word?
06 July 2013 1,311 15 View
Please if someone could explain that how can I check the lifetime of RF MEMS switch or any other structure (example or switch) which makes contact with signal to change the state in COMSOL!
06 July 2013 5,169 2 View
When we provide bias voltage, due to electrostatic force the membrane gets displaced towards electrode/s, but how to check the elastic recovery forces of membrane, i.e., will the structure returns...
06 July 2013 6,543 1 View
I want to know that whether it is possible to grow a layer of graphene on gold, if yes then how?
06 July 2013 8,985 2 View
Could you recommend some articles on Urban Transportation System optimization and Innovation?
13 August 2024 2,595 3 View
I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...
13 August 2024 9,795 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...
31 July 2024 5,785 4 View
After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?
29 July 2024 4,955 0 View
Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...
28 July 2024 6,553 1 View
Hi there, I'm new to modelling with comsol. I would like to ask if it is possible for comsol to output linearly polarized (LP) modes? I tried modelling a simple single mode fiber with an enlarged...
23 July 2024 4,019 3 View
Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...
21 July 2024 1,680 2 View
We invite qualified candidates of Visiting Scholars to engage in research collaboration or deliver lectures on their research, with travel expenses covered. The visiting period is flexible,...
20 July 2024 1,165 1 View
Undefined variable. - Variable: comp1.cNa - Géométrie: geom1 - Domaine: 1 Failed to evaluate expression. - Expression: comp1.cNa - Affichage: Graphique sur ligne 1
19 July 2024 1,938 2 View