Greenhouse Simulation using COMSOL Multiphysics ?

Have anybody tried to simulate greenhouses using COMSOL Multiphysics? and is it doable?

26 December 2020 803 1 View

Did anyone used microflow imaging to measure the size distribution of Multivesicular liposome which are charcterized with size (>3um)??

I have prepared Multivesicular liposomes using the following procedures: Multivesicular liposome formulations for the sustained deliv... Multivesicular liposome (MVL) sustained delivery of a...

18 November 2020 3,189 2 View

CROs or collaborators for assay of non-ATP competitive kinase inhibitors?

We have compounds that showed activities against variety of kinases. However, since they have been designed to bind to the peptide site on kinases, I need to investigate this mechanism. Please...

15 November 2020 2,040 3 View

I followed a common procedure to synthesize Fe3O4 nanoparticles. The problem is that XRD pattern does not show any crystal structure. Could you help?

Besides, I have performed different characterization tecniques to my Fe3O4 nanoparticles and all are similar to what is reported in literature. Those characterization techniques include FTIR, SAED...

22 July 2020 8,549 12 View

Please recommend biological investigation of newly identified anticancer compounds that specifically inhibit Src kinase?

We aim to publish ta high impact journals (If 6+). Compounds showed incredible activities on cancer cell line (submicromolar on several types). I need your recommendation on how to determine...

24 May 2020 1,230 3 View

To what extent do top-down language policies influence language use?

I'm often very skeptical about the language decisions and policies issued by governments or self-proclaimed language authorities to control the way people use language. Nevertheless, I'm just...

28 February 2020 5,904 4 View

No title

19 September 2019 5,877 1 View

Will a power fail affect my cDNA synthesis?

14 September 2019 8,969 3 View

What are the main reasons that may lead to failure of plans in tourism? and how to change it?

I believe that the concept of tourism planning is to face the expected operational errors, (on paper), before starting the implementation phase of the tourism project itself. Thus, this may lead...

08 June 2019 389 5 View

Which nucleases can degrade G-quadruplex ?

I am interested in the effect of different nucleases on G-quadruplex DNA. I see examples in the literature where exonucleases or endonucleases release G-rich sequence which consequently form...

31 October 2018 908 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View