How to do buckling analysis in ansys apdl for laminated plate with PZT 5H attached?

I am doing buckling analysis of laminated plate surface bounded with two piezoelectric PZT 5H and axial compressive load is applied. I am getting an error, No ANEL table exists for material 2....

16 February 2021 510 1 View

What to do if I am doing a Meta Analysis of Exploratory studies and the studies do not have effect size??

I am doing a meta analysis of imaging exploratory studies which themselves did not have effect size. Therefore, I am unable to compute the variability in the effect sizes in my meta analysis. What...

18 January 2021 4,881 4 View

I could not find a publication that fits the idea of evaporation together with DPD. Any suggestions?

I did find some papers that incorporate the two ideas together but I could not follow the research methodology. The simulation results were remarkable but not self explanatory. I tried to follow...

20 September 2020 5,354 4 View

Are there effective measures to prevent substantial economic loss due to blister beetle (Mylabris pustulata) in early pigeonpea?

Pigeonpea is a preferred host to adult blister beetle (Mylabris pustulata). Early pigeonpea, which is sown during May 15-June 15 in North West and north east plains of India, enters into flowering...

28 July 2020 1,278 8 View

Whether application of data science is equally important in agriculture including crop improvement??

In recent years, data science has emerged as a promising interdisciplinary subject, and helped understand and analyze actual phenomena with data in multiple areas. The availability and...

08 June 2020 6,514 6 View

Whether agriculture in India is robust enough to contribute substantially so as to minimise the expected decline in GDP in post Corona scenario??

Before the Corona pandemic, agriculture sector in India contributed around 15 percent to the total GDP growth. In the present scenario, service and industrial sectors are bound to pull down the...

27 April 2020 9,608 11 View

Does the occurrence of one disease affect the intensity and severity of other diseases in plants??

Cool season pulses such as chickpea, lentil, grass pea, faba bean, etc are affected by a number of root and foliar diseases. Empirical observation revealed that there was minimal incidence of root...

26 March 2020 724 26 View

Is the research field of nanofluids saturated or any new field/application is still underestimated?

I am working on the enhancement of heat transfer using nanofluids from the past few years. But sometimes, I think that the research in the applications of nanofluids is saturated. If not, what are...

27 February 2020 4,764 9 View

WHAT IS "ML" term in InAs/GaSb superlattice mid-wavelength infrared pin photodiode structure?

I am implementing InAs/GaSb superlattice mid-wavelength infrared pin photodiode structure in SILVACO ATLAS. I am not able to understand what does" ML" in device structure means and how can i do...

22 January 2020 9,283 6 View

Is it scientifically correct to consider the nanodusty plasma as an electron depleted dusty plasma?

In nanodusty plasma, dust density is higher than normal dusty plasma. In numerical modeling, it is assumed that it is electron depleted dusty plasma. They ignore the electron charge in compared to...

13 January 2020 3,925 5 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

No title

02 March 2021 3,060 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View