I am adding Cu nanoparticles as reducing agent and not much sure.
Thanks Sir. It is very helpful paper
I am melting Zn based solution in furnace, the solution is in Ceramics crucibles but after heating at 900 C the obtained powder is dark grey colour (Not white) is sticking hardly to crucible (so...
07 August 2018 1,308 14 View
Dear Researchers: I am wondering after getting FT-Raman spectra, Ge Diode of Graphite, Graphene oxide and Graphene. All results shows only one peak (2D) around 2900-3100 cm-1 , even graphite...
04 May 2018 9,907 4 View
I am fabricating multi-layer PDMS stamp for nano lithography. Unfortunately I am not able to get good pattern transfer from silicon template after molding on the template. After fabricating, for...
03 April 2018 7,402 5 View
Hallo: I want to see the exchange current in charge transfer reactions at TiO2 films -0.6M NaCl solution interface.I want to know about the redox potential of my solution as its very important to...
02 March 2017 5,469 4 View
Well, Its kind of annoying to get Impedance/OCP results different for every new sample. Samples prepared and processed with same parameters and using same pH electrolyte. Samples are commercial...
31 December 2016 4,892 1 View
I want to measure pre polarization potentiostatic (for different times), So can i use same working electrode for different measurements while not changing my solution and working electrode, or...
31 December 2016 8,082 4 View
I have measured and got MC plots for titanium oxide on titanium substrate. Measurements were done with different pre-polarization time galvanstatically. On some samples i have received negative...
31 December 2016 1,408 18 View
I am interested in Graphene nanoparticles to be used as super hydrophobic and anti-reflective smart coatings. I haven't started any experimental techniques but doing literature review for my...
05 June 2016 4,727 3 View
I have received XRD results of Graphite, GO and Graphene sample. I got peak of highest intensity at 26degree in graphite sample. The intensity of peak at 26deg is reduced and other peak with small...
03 April 2014 2,185 6 View
What ranges of D and G peaks will suggest that Graphene and Graphene Oxide is synthesised as in the literature there are alot of variations like D peak ranges from 1320 to 1365 G Peak ranges from...
01 February 2014 9,762 28 View
I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.
09 August 2024 9,894 2 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View
I want to know more about Magnetite deposits.
06 August 2024 1,066 0 View
I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?
03 August 2024 4,624 3 View
Is this circle one of the rings?
03 August 2024 5,988 0 View
Hello, if you made a transwell assay where you incubate the cells with a nanoparticle-encapsulated drug and considering that in the oposite compartment you'll have both the free and encapsulte...
03 August 2024 2,730 1 View
I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...
01 August 2024 8,368 2 View
Following curve related to Co0.6Mn0.4Fe2O4 Magnetic nanoparticles with extra phase a-Fe2O3. I will appreciate to help me to interpretation this spectroscopy, especially the blue line.
31 July 2024 9,140 2 View
The starting material is a finely ground powder. Some particles contain more graphene than others.
30 July 2024 3,978 2 View
Dear all: I am modifying Bismuth Tungstate with Hematite (Fe2O3), so I would like to know about how much Iron(+3) can form a solid solution in a Bismuth Oxide matrix. Best wishes Marco
29 July 2024 2,163 1 View