Anyone know how to use bladegen in ANSYS?

More Chinedu Isiadinso's questions See All

If you have experience with implementation of Meshless Methods with Radial Basis Functions, can you please send me an email?

I am using radial basis functions for a current problem, but these basis functions do not satisfy the kronecker-delta condition like the finite element basis functions. I would like to have a...

19 March 2024 7,594 0 View

What is the connection between sizre of supercells, k points, cut off energy and convergence?

does increasing or decreasing size of supercells affect these in DFT calculation?

17 March 2024 7,374 3 View

A project in supercapacitors?

which carbonaceous material will be good to study the performance of carbon materials in supercapacitors?

17 March 2024 5,365 2 View

Please how do i describe the SEM images of these Porous carbon?

Are there specific things i must mention when describing these images/

03 January 2024 7,759 5 View

Pleass what's the effect of changing salt template ratio in preparing porous carbon?

I had a laboratory course about synthesis of porous carbon but the salt template ratio was changed from 1:1 to 1:10. Why?

02 January 2024 5,914 0 View

How can one differentiate between direct carbonized carbon and salt template method?

Hello, i prepared porous carbon using direct and salt template method. i thought the salt template should only give mesoporous carbon but i got hysteresis in the two methods. How do i explain that...

31 December 2023 6,474 4 View

What type of spectroscopic transitions is observed in NMR?

What are the typical excitation frequency

20 December 2023 7,922 2 View

Please why is the NMR considered a very low sensitive method when compared to other methods?

I heard it has to do with the population ratio, energy difference and Boltzmann factor.

19 December 2023 6,094 3 View

How do i explain SEM images of porous cxarbon?

How can i know if it microporous, mesoporous or macroporous or moixture by mere looking is there a way to analyse before further using physisorption?

10 December 2023 700 2 View

How do i Interpret the result olf TEM and SEM of csrbonaceous materials?

I want to know how i can use SEM and TEM micrographs to discuss mesoporous and microporous nature of materials

28 November 2023 378 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

Cp of Turbine is ever increasing with Tip Speed Ratio. What Could be the reason??

I am a student of Mechanical Engineering. I am doing CFD opf Archimedes Winf Turbine. I am trying to validate the result of Paper. But the problem is that tha value of Power Coefficient is ever...

05 July 2024 6,839 2 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View

Yang-Hsu Liao

if you want to use your CAD model, you have to transfer it into IGS or IGES file, so that you can import to bladegen and use your original design.

Ruhollah Mahoori

i want import my CAD model to bladegen, but in step3 (definition Meridional) i dont know How to do it?

Thanks in advance

Arman Asgharpoor

you can find tutorial here:

https://dlscrib.com/downloadFile/5899a5456454a78d26b1eb36