How do i Interpret the result olf TEM and SEM of csrbonaceous materials?

29 November 2023 1 390 Report

I want to know how i can use SEM and TEM micrographs to discuss mesoporous and microporous nature of materials

Chinedu Onyeke, you can interpret TEM and SEM images of carbon materials by examining pores and their sizes. In SEM, analyze surface features such as particle size and shape, while TEM allows for direct observation of internal structures. Consider the following pore size ranges: Micropores (< 2 nm) and Mesopores (2 - 50 nm).

I hope you find these helpful.Warm regards

Badges
Science topic

More Chinedu Onyeke's questions See All

If you have experience with implementation of Meshless Methods with Radial Basis Functions, can you please send me an email?

I am using radial basis functions for a current problem, but these basis functions do not satisfy the kronecker-delta condition like the finite element basis functions. I would like to have a...

19 March 2024 7,594 0 View

What is the connection between sizre of supercells, k points, cut off energy and convergence?

does increasing or decreasing size of supercells affect these in DFT calculation?

17 March 2024 7,374 3 View

A project in supercapacitors?

which carbonaceous material will be good to study the performance of carbon materials in supercapacitors?

17 March 2024 5,365 2 View

Please how do i describe the SEM images of these Porous carbon?

Are there specific things i must mention when describing these images/

03 January 2024 7,759 5 View

Pleass what's the effect of changing salt template ratio in preparing porous carbon?

I had a laboratory course about synthesis of porous carbon but the salt template ratio was changed from 1:1 to 1:10. Why?

02 January 2024 5,914 0 View

How can one differentiate between direct carbonized carbon and salt template method?

Hello, i prepared porous carbon using direct and salt template method. i thought the salt template should only give mesoporous carbon but i got hysteresis in the two methods. How do i explain that...

31 December 2023 6,474 4 View

What type of spectroscopic transitions is observed in NMR?

What are the typical excitation frequency

20 December 2023 7,922 2 View

Please why is the NMR considered a very low sensitive method when compared to other methods?

I heard it has to do with the population ratio, energy difference and Boltzmann factor.

19 December 2023 6,094 3 View

How do i explain SEM images of porous cxarbon?

How can i know if it microporous, mesoporous or macroporous or moixture by mere looking is there a way to analyse before further using physisorption?

10 December 2023 700 2 View

How can Mott-Schottky Analysis be used to determine the flat band potential and donor density ?

how exactly cab be used for example in this case

24 November 2023 8,407 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View