Which chemical will be the best choice for inducing ROS stress? Cobalt Chloride, H2O2 and monosodium iodoacetate (MIA) ?

I wish to induce stress conditions to Adipose derived mesenchymal stem cells and for that i have these three available chemicals. Your expertise are needed.

07 August 2018 5,132 10 View

What is the best total plant extracts isolation protocol?

07 August 2017 1,225 4 View

What if my GAPDH expression is different in Osteoarthritis and Normal model?

03 April 2017 6,285 2 View

Can anyone please share article on different types of scaffolds preparation?

09 October 2016 4,733 0 View

What's the better way to preserve DNA and RNA. Water or Buffer and Why?

Usually i preserve it/elute it in water but i need to know whether buffer is good than water or not?

08 September 2016 3,130 23 View

What is your opinion about genetically modified crops?

02 March 2016 5,594 4 View

Should we focus on transgenic crops production? Is cisgenesis or intragenesis approach good enough to be replaced instead of transgenesis?

I need answer as i have to present a topic on recent advances of Genetic engineering for the production of fruit/crops (bio-safety prospective).

01 February 2016 6,795 3 View

Which genome editing technique is the best, efficient and reliable among ZFN,TALEN and CRISPR CAS9?

I wish to know this for the feasibility and reliability as well as accuracy.

31 December 2015 2,412 3 View

What will be the best Acid to change the PH of a buffer up to 8.0. Either i should use Strong acid or weak acid and why???

Just wish to know if there is any effect and if there is any, so how?

31 December 2015 8,637 0 View

How will we explain 1 ward distance in hierarchical cluster analysis?

It means if two ethnic groups have one ward difference then what will be our explanation for them.

05 June 2013 179 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

No title

02 March 2021 3,060 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View