Can i use Oryzalin to produce polyploid Begonias ?

Begonias are sensitive to Oryzalin herbicide and it is not used for Begonia Polyploidy studies and i doubt if Begonia mini cutting can survive Oryzalin Treatments . I want to use this article as...

31 December 2016 3,033 5 View

How to keep magnesium sulfate and ammonium phosphate in one liquid hydroponic fertilizer solution ?

magnesium sulfate and ammonium phosphate are not compatible but companies made dry powder fertilizers that have both of them .I want to make a fertilizer solution that have this two chemicals in...

05 June 2016 5,360 4 View

Is it possible to induce tetraploidy in marigold to increase their nematicidal activity ?

Nematicides are dangerous chemicals and not safe for the environment, farmers and lakes of good nematicides. They cause crop failure especially for small farmers. Marigolds have nematicides in...

11 December 2013 8,542 11 View

What is happening when there are two embryos in one lilium seed?

I find one seed with two embryo in my intersectional hybrid seeds from trumpet (seedling) X Oriental Hybrid "Montezuma", both of them germinate in MS medium before the embryo abortion due to lack...

09 October 2013 8,101 4 View

How to prevent callus browning in rose callus culture?

I have callus of several rose varieties (6 cutflower variety , 1 miniature and 1 garden variety) but I don't know why they turn brown. The medium and callus is still fresh and the explants are not...

05 June 2013 5,289 31 View

Protocol for in vitro selection of salt and lime tolerant clones and seedlings in Lilium species?

I need a moderate to easy method and protocol for the selection of salt and lime (calcium carbonate) tolerant clones and seedlings of Lilium species. In vitro grown seedlings and micropropagated...

04 May 2013 300 6 View

Is it possible to obtain diploid or tetraploid plants in micropropagation of Triploid lilium hybrids (somaclonal variation in ploidy level)?

Is it possible to induce somaclonal variation in ploidy level in micropropagation of Triploid Lilium Hybrids? I am interested in inducing somaclonal variation in ploidy level of triploid lilium...

01 February 2013 4,742 5 View

How to control bacterial infection in a plant tissue culture?

I have very big problems with some bacterial contamination in my cultures, Tuberous Begonia, Echinacea Purpurea, Lilium Ledebourii. Not all of my cultures are infected but contamination reduces my...

01 February 2013 8,345 22 View

Why is the potato product forming thin shoots in a tissue culture?

I started to culture potato eyes in a tissue culture medium and got one growing shoot. The problem is there are very thin side shoots of this growing potato. Does anybody know how I can resolve...

31 December 2012 3,352 13 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

No title

02 March 2021 3,060 3 View

Which is the best place in the world for the plant biotechnology research?

I am searching for a good place for the Post Doc,

02 March 2021 4,053 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

Which cell line should we use to perform biological dosimetry experiments?

We are preparing some experiments based on irradiating cells under different conditions in order to evaluate the effects in terms of DNA damage, genetic expression, etc. As our project is...

01 March 2021 3,355 3 View

Which bacteria are suitable for quorum sensing screening?

I want to find a quorum sensing inhibitor from plant extracts. Klebsiella pneumoniae, Moraxella catarrhalis, Staphylococcus aureus, and Streptococcus pneumoniae. I looked for these strains...

01 March 2021 7,675 3 View