ANSYS Fluent: How to simulate water spray injection in narrow duct?

Ahmed Y Taha Al-Zubaydi @Ahmed_Al-Zubaydi

03 March 2018 0 7K Report

I have a problem with simulate a spray in narrow duct channel in ANSYS Fluent (My duct is 6 mm height) ...Any hints??

Badges
Science topic

More Ahmed Y Taha Al-Zubaydi's questions See All

How do you calculate pitch angle in Folds?

Structural Geology

10 March 2023 3,993 2 View

What theories explain the occurrence of geological structures?

Structural Geology

10 March 2023 4,636 15 View

How can you study the technical and economic feasibility of mining projects؟?

Mining geology

10 March 2023 6,882 12 View

Which of the following rocks has greater compressive strength Granite - Limestone, Schist and Why ?

Rock mechanics

23 February 2023 9,572 3 View

How are natural resources sustainable?

Mining geology

16 February 2023 9,855 13 View

How do you calculate the surface roughness of the discontinuities?

Discontinuites

15 February 2023 399 2 View

How do you calculate the normal stress of rocks?

Rock Mechanic

07 February 2023 9,146 4 View

Which is better to draw the joints geometrically" using the Rose diagram or the Stereonet diagram?

Joints

26 January 2023 5,081 3 View

Which is the best type of Geogrid to use for soil improvement and stabilization?

Soil Mechanic

26 January 2023 4,168 2 View

How to calculate the unconfined compressive strength with a point load test?

Rock slope engineering

16 January 2023 2,203 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

What is the difference between alluvial and fluvial?

I have made an unpleasant discovery that I seemed to use these terms incorrectly. 'Alluvial' seems to mean "out of the river channel", flood-plain' etc. While all these cross-bedded...

15 July 2024 2,073 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to add channel doping variation in sentaurus tcad to see its effect on transfer characteristics of mosfet?

I am getting trouble in studying the effect of channel doping variation in forksheet structure for p and nmos.

08 July 2024 2,074 0 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View