The science, art, or technology dealing with processes involved in the separation of metals from their ores, the technique of making or... | Contact experts in Metallurgy to get answers
2,505 views 637 posts
Questions related to Metallurgy
Iron and Steel making, Stainless steel making
06 June 2016 8,648 1 View
Precision of orientation and misorientation angle+axis are crucial in terms of analyzing the EBSD data in very smaller ranges. For reference, I am attaching Wilkinson 2001 paper on exactly same...
26 May 2016 1,599 5 View
The effect of Al alloying on the deformation behavior of hcp Ti is summarized. It is found that the hardening rate (i.e., the slope of CRSS vs. Al concentration curve) of prismatic slip is higher...
18 May 2016 8,841 9 View
i need TTT diagram
17 May 2016 9,076 3 View
Is there any way to quantify the volume percent of recrystallization?
15 May 2016 3,173 4 View
Hello, I have an aluminum plate, 1mm thick, but I need what side of it to be non-conductive AND prous (a few micrometer pores, 50% porosity). I thought transforming a few micrometers of aluminum...
05 May 2016 6,733 2 View
05 May 2016 3,027 6 View
a book that explains step by step mathematical calculation of parameters to design a deep drawing die
05 May 2016 4,500 6 View
Hello Researchers, I have Nickel, Manganese and Tin powder (particle size is less than 100 micrometer for all). I want to make single phase alloy by arc melting technique. Oxides are not desired....
05 May 2016 7,347 5 View
05 May 2016 7,069 4 View
05 May 2016 6,572 5 View
Hi all Currently we are trying to perform the standard method of ISO11494, but due to the standard only goes up to 95% fineness and we would like to increase to 990 or even higher. Does it seems...
05 May 2016 5,063 0 View
Grey cast iron has a small amount of graphite that shouldn't be in nodular shape. By adding Magnesium (with less amount of Calcium) and Sulfur, the morphology changes to spherical. This morphology...
05 May 2016 2,160 4 View
05 May 2016 4,005 3 View
we annealing Haynes 188 (Co-base alloy) in different temperature and after we observed some twining in it (annealing twin). i want comparison whit together, i estimate volume fraction of twin...
28 April 2016 4,243 2 View
Is there any effects of aluminum oxide layer located on the Al billet surface during cold forging? Especially during reduction process? Does it effect the friction in a good or bad manner? Does it...
28 April 2016 6,592 3 View
-
27 April 2016 9,012 1 View
please suggests the % phases for the fig. shown here.
26 April 2016 7,653 4 View
What can be done in order to improve the interface adhesion between Al2O3 particles and Fe Cr alloys in process of metal infiltration? is there some difference in the adhesion by using "brown" or...
26 April 2016 5,016 3 View
D.G. ESKIN
25 April 2016 8,961 0 View
I know in 2-D, there are five degree of freedom for a grain boundary, therefore there should be a 5by5 rotation matrix for it. Determining this 5*5 matrix is my target. Thanks
20 April 2016 3,414 4 View
heat treatment, material thickness
19 April 2016 396 15 View
As we kown, some kinds of corrosion products are easy to be oxidized, so could somebody tell me how to avoid the oxidation of corrosio products during processo di salvataggio and pre-processing...
19 April 2016 2,228 5 View
While, heat treating a steel (cooling or heating) at a rate different from equilibrium heating or cooling rate, transformations take place at temperatures higher than or lower than the temperature...
16 April 2016 5,555 3 View