Contact experts in FLUENT to get answers
10,357 views 3,636 posts
Questions related to FLUENT
Hi Lattice Boltzamnn and CFD experts, I'm implementing MPI for a 3D lid-driven cavity flow using a basic setup with just two processes. I have successfully implemented it with a simple case where...
14 July 2023 3,915 0 View
Reservoir Engineering 1. Whether Stokes equation that characterizes low Reynolds number incompressible flow of a single-phase Newtonian fluid in a rigid porous medium governed @ pore-scale with...
14 July 2023 4,753 0 View
I'm running a surface reaction. I'm wondering how does ANSYS Fluent calculate the surface deposition rate? Thank you.
14 July 2023 729 2 View
Some time density purify fluid.
14 July 2023 7,869 0 View
I want to see the correlation between PM2.5 and Ozone over different regions in India, which data shall be used daily mean or hourly mean data
10 July 2023 7,059 2 View
Hello everyone, I want to use an input parameter from workbench to define the specific heat of my working fluid. Do you have any idea how to do this? Should I use udf? The Cp is not dependent on...
03 July 2023 9,610 3 View
Weather stations are key facilities to record long-term change in surface air temperature (SAT) in land. However, some weather stations are located in or near cities, and they may suffer from...
21 June 2023 9,020 2 View
Dear ResearchGate community, I am currently working on a steady-state thermal analysis of a hollow wall in Ansys Fluent where a low emissivity insulation material is attached to the inside of the...
14 June 2023 9,952 2 View
How can the experimental results of small-scale marine structures be applied to the force calculation of large-scale marine structures?
01 June 2023 8,079 0 View
Hello! We pump the contour of a metal tube with a diameter of 3 mm with oil with a viscosity of 0.0031 kg / m * s (abt. the viscosity is 4 times higher than that of water). We are interested in...
31 May 2023 3,900 8 View
i need way to extract the nodal coordinate of deformed shape i use this but show just coordinate of undeformed shape Main menu > List > Nodes > (Coordinates only) Main menu > List...
27 May 2023 345 0 View
I want to make a simulation for 400 time steps, how can I give in Ansys Workbench?
22 May 2023 5,913 4 View
I am using openfoam to calculate the flow field of a rectangular section channel with a cage in it and try to analysis the influence of the blockage on particles transport. I plan to inject...
14 May 2023 4,552 2 View
Hi all, I am currently working on simulating a water jet problem, where water is injected from the left boundary and exits the domain through the right boundary. However, I am facing a challenge...
11 May 2023 2,517 9 View
I have been searching for ASTM/ISO standard procedure to determine the tensile properties of shape memory filament used for 3D printing. I have come across ASTM D638 but this procedure uses 3D...
03 May 2023 5,581 1 View
I am working on simulation of savonius hydrokinetic turbine in cfx. I have set inflation layer on turbine as shown in photos. It is observed in the previous investigation that, the non-dimensional...
24 April 2023 3,090 3 View
I'm studying the combustion of boron particles in a combustion chamber. Because the surface of boron particles is covered with boron oxide, the combustion of boron particles is divided into two...
21 April 2023 2,702 2 View
I was trying to use chtMultiRegionFoam solver but it shows fatal error.
06 April 2023 4,904 0 View
Hello, I would like to know how to simulate water diffusion through a porous region using Ansys Fluent. Specifically, I am interested in simulating the following problem: There is a pipe with...
15 March 2023 4,314 1 View
I want to use Ansys fluent to calculate the temperature field and velocity field. My model contains a sealed box in which is 1/3 medium and 2/3 air. I set a constant energy source in medium（...
14 March 2023 8,386 10 View
any commands or others commands can find the value?
08 March 2023 7,655 1 View
Which PHP heat pipe thermal performance is better close end pulsating heat pipe or closed loop pulsating heat pipe?
05 March 2023 4,218 1 View
I have one condition, that I have to show S21 results too
02 March 2023 6,518 0 View
Currently, I am generating 3D multiblock, structured mesh in pointwise software. During boundary condition setting process, some surface left unspecified. During simulation these unspecified...
23 February 2023 2,968 0 View