Would you recommend Simscale for Simulation ?

Manigandan Sekar @Manigandan-Sekar

20 January 2018 1 5K Report

Now am using Ansys and StarCMM+ for CFD simulation. Did anyone used SIMSCALE ? How is the environment and result plots

Badges
Science topic

More Manigandan Sekar's questions See All

Dear all, Is there any model available to predict the "possible diseases" based on the available pollutant concentration in air ?

In detailed human health risk assessment models. Is there any model that can predict the possible disease.

21 December 2020 7,535 5 View

How to get best LSTM model for regression problem? how to tune or select hyper parameters?

How to get best LSTM model for regression or prediction problem? how to tune or select hyper parameters?

29 June 2020 9,377 4 View

How to work with phasor model in matlab?

I am running IEEE 13 bus model in MATLAB with discrete time . But when I connect Renewable energy DFIG model with IEEE 13 bus system not working due to phase model of DFIG. How to rectify error?

31 January 2020 7,950 4 View

In fluent heat flux analysis results are not converging ?

I had solved the heat flux analysis of the multi-domain problem in fluent. Even after the 20000 iterations also the solution is not converging. As the iterations increase the results are diverging...

05 November 2019 1,713 3 View

Any specific procedure to be followed while converting one dimensional data into image?

Is there any specific procedure to convert 1D data to image before feeding convolutional neural networks ?

18 October 2019 8,309 4 View

Is there any open source Software In Loop (SIL) test method.?

Is there any open-source Software In Loop (SIL) test method available to test the network that was actually created in MATLAB. Anyone guide or give reference to use OPAL-RT testbed to integrate...

06 October 2019 8,124 1 View

Do addition of nanopartilces in soil increases the Plant yield ?

Can any one explain me that addition of nanoparticles enhances the growth of plant and produces more yield. If so, can anyone list me the nanoparticles i can use Plant is Tomato and Aubergines

24 June 2019 5,402 3 View

Do anyone have working protocol for cardiac perfusion in mice?

I am new to perfusion. I need to do cardiac perfusion in mice and my area of interest is brain further to sectioning and IHC. Does anyone have standard protocol of cardiac perfusion for this. Help...

29 May 2019 6,919 3 View

Is addition and removal of Co-author during submission of revised article is acceptable @Elsevier ?

I like to know the removal, addition and shuffling of co-authors is against moral and ethics in Elsevier Journals. Is it necessary to contact a editor to make such changes

20 February 2019 3,676 18 View

How to gelatin coat flasks for primary rat astrocyte culture?? Suggest me with how much percentage gelatin should i use??

I'm gonna culture rat mixed glial cells for first time. suggest me with how much percentage gelatin should i use to culture cells..

07 November 2018 7,023 6 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View