Nanoparticles Iron oxide Acid HCl coating
It will depend on the temperature of the dispersion
So if the temperature is high then the coated particles might get dissolved? Is it so?
Yes you could start hydrolyzing your polymer with acid as catalyst
You may want to check section 4.4.1., entitled 'Partial acid hydrolysis', of the signalled technical-commercial document available from 'Amersham Biosciences' (reference code: 18-1166-12):
http://tdbcons.com/images/pdf/18116612_AA_p13.pdf
The characteristic raman spectra that I've obtained for graphene like quantum dots shows a kink at about 1450 cm-1, this is different from the reported literature. What can be the posible reason...
01 February 2020 2,243 3 View
I've a nano-scaled graphite like material, the XRD pattern is showing some peaks which are not matching with any of the reported literature. For example usually a broad peak is seen around 21...
01 February 2020 6,185 2 View
I have to analyse the change in composition of acetonitrile after being reacted mechanically at different time intervals, hence I'm planning to undertake a GC-MS of the samples. Can anyone suggest...
05 June 2019 9,128 8 View
What kind of synthesis is this SSM route useful for?
03 April 2018 9,998 2 View
I'm using a PDA detector HPLC unit, I was wondering whether it is possible that the retention time can change for a particular compound when the detector is set at a different wavelength, all...
11 December 2017 5,337 6 View
I'm withdrawing samples after a 15 minute interval for 90 minutes. Hence, the 90th minute sample is to show the highest amount of degradation or the least peak area, but it shows the highest, this...
10 November 2017 5,853 7 View
How to identify crystalline phase data from the XRD data of the said crystals
08 September 2017 345 2 View
In most research papers the wavelength chosen for DBT detection is 284nm, but according to the NIST data the maximum absorbance occurs around 230-240nm. Can anyone explain why it is...
07 August 2017 3,923 4 View
07 August 2017 8,177 4 View
07 August 2017 5,576 4 View
I looking for ferro calcium production process
03 March 2021 1,755 4 View
Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru
02 March 2021 1,787 2 View
I anwar by adsorption or reaction ..but it is either more method...
02 March 2021 4,811 2 View
I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...
02 March 2021 7,626 1 View
[Synthesizing Cu nanoparticles without using chemical reductants]
01 March 2021 8,359 1 View
Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...
01 March 2021 8,220 2 View
In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...
01 March 2021 2,207 3 View
I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...
01 March 2021 3,703 3 View
I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?
01 March 2021 930 3 View
I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....
28 February 2021 7,967 3 View