Indium doped SnO2 films onto glass
01 February 2019 6,445 2 View
HI In the study tree i have four steps time dependent step 1 time from(0-10) step 2 (10-20) step 3 (20-30) step 4 (30-40) ,i want to combine the last three steps (10-40)in a single plot,How is it...
02 December 2018 3,683 3 View
I have an equation of the temperature of the soil according to the time and the depth my question is how to introduce it in COMSOL (heat transfer in solid physics)?and how to start computing in a...
25 January 2018 7,070 6 View
HI all; I am using Ansys 16 fluent .in order to have node to node mesh i used a conformal mesh by modifying multiparts multibodies to one part multibodies when exporting the mesh file to fluent i...
20 November 2017 6,454 2 View
Please First, i need to make a pH 7.4 phosphate buffer (0.1M), for a microbiology experiment, but i am missing KH2PO4, NaH2PO4 and Na2HPO4. . I have K2HPO4 and NaOH, how can i use these two...
25 July 2016 691 13 View
Hello I am not very familiar with meshing geomytries specially 3D ones. I really appreciate if you provide some input.my geometry is a helical pipe(heat exchanger) wich circulate water inside it...
27 February 2016 8,841 3 View
front metal contact (Ag, Al or Au) solar cell such Ag/SnO2/Si/Al
01 January 1970 9,178 8 View
It is a very interesting project, I would like to know the nature of the electrodes used if possible?
01 January 1970 6,580 2 View
What is the best measurement method to determine bulk concentration, resistivity and mobility of thin films?
01 January 1970 7,287 11 View
transmittance increases till a peak and descends to valley within Vis
01 January 1970 8,276 2 View
We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...
03 March 2021 7,975 3 View
I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...
01 March 2021 395 3 View
Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !
01 March 2021 2,501 3 View
I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?
01 March 2021 930 3 View
Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.
28 February 2021 3,640 3 View
I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...
27 February 2021 6,801 3 View
24 February 2021 2,362 5 View
I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium
24 February 2021 1,915 1 View
Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...
24 February 2021 3,785 3 View
As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...
24 February 2021 1,349 1 View