While trying to do the simulation of the gan hemt on tcad sentaurus, do we need to fit the mobility with the given hall mobility in the experiment ?

20 March 2024 0 8K Report

do we need to change the GaN material mobility in tcad with the hall mobility in the experimental paper? and do we need to match the sheet charge density too? Is this sheet charge density calculated from the electron density?

Badges
Science method

More Shivansh Awasthi's questions See All

I am trying to simulation a double channel hemt on Sentaurus TCAD but Transferred Electron 2 model is not working? Can anyone help to understand ?

The mobility model that I am using is DopingDependence model and Transferredelectrton2 for high field degradation of mobility by intervalley scattering. This should reduce the current but it is...

13 March 2024 1,781 0 View

I am simulating Id-Vg from Vg -6 to 2 V GaN HEMT on Sentaurus TCAD, Can someone please tell as how to remove the issuedescribed below?

Solution is not converging after gate voltage reaches 1.34 V and Id is 200mA

13 March 2023 2,765 1 View

I am simulating a GaN HEMT on Sentaurus TCAD, I am facing a error as RHS value is exceeding 1e20. Can someone please tell as how to remove the issue?

min step=1e-3 max step=0.01 minstep=1e-5 increment =1.55 , models is hydrodynamic, math i have tried with default and also blocked and pardiso

01 March 2023 8,320 2 View

I am trying to take a FFT of a transient response ( sin wave) on ATLAS (SILVACVO) but I am not a getting a proper DC offset value?

I am changing the fundamental frequency and the maximum harmonic value and the dc offset is coming different every time. how do I set the accurate parameters?

03 October 2021 9,433 3 View

How to the solve convergence problem with the Q factor in quantum model while using it in GaN HEMT(Silvaco ATLAS) ?

solve qfactor=0.0001 solve qfactor=0.0005 solve qfactor=0.004 solve qfactor=0.02 solve qfactor=0.1 solve qfactor=1.0 trying out all the combinations but still convergence issues

10 December 2020 9,796 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View