Binder for reinforced plastics with fluidity temperature 100-120C, prepreg on its base containing >50% carbon filaments and examples of articles made?

Binder for reinforced plastics with fluidity temperature 100-120C, prepreg on its base containing >50% carbon filaments and examples of articles made of it. We seek for prepregs with at least...

07 August 2018 1,037 0 View

Adhesive for carbon and/or glass filaments sustaining -150C + 150C?

We need Adhesive for carbon and/or glass filaments sustaining -150C + 150C? It may be like PolyAmide Imide adhesive or adhesive cured by UV, or any combination of adhesives.

07 August 2018 2,898 5 View

Polyimide based on Diamine R?

Polyimide based on Diamine R? for preparation of thermal-resistant Polyimide powder

05 June 2018 704 2 View

What is more important than success in our Living?

My previous question was: """To be successful in life - what does it mean?""" Almost all the answers to this question were about: "What is the Success? and how to reach the success" - a...

03 April 2018 2,019 96 View

How to remove from the Metal surface the PSA adhesive?

How to remove from the Metal surface the PSA adhesive by using non-aggressive solvents? What type of solvents would you recommend? at what temperature?

03 April 2018 5,489 6 View

What are the best solvents to precipitate Aromatic PolyAmic Acid from its solution in DMF or DMAC?

What are the best solvents to precipitate Aromatic PolyAmic Acid from its solution in DMF or DMAC?

31 December 2017 4,598 2 View

How to obtain a precipitated powder of Poly-Amic Acid based on aromatic diamine and aromatic dianhydride?

How to obtain a precipitated powder of Poly-Amic Acid (PAA) based on aromatic diamine and aromatic dianhydride? It is well known that for several Aromatic Polyimides (PIs) in the course of...

11 December 2017 2,072 2 View

Band assignments for FTIR spectra of Ground Rubber Tire Crumps?

FTIR spectra of GRT are difficult to "read" because of carbon filler. The bands are broad and have of very low intensity. As a whole the contribution of the spectrum of GRT to the total spectrum...

09 October 2017 6,952 6 View

Thermo-resistant Rubber for Gumming Calender Shaft?

We are looking for manufacturer/supplier of Super-Thermo-Resistant Rubber for Gumming Calender Clamping Shaft. We'd greatly appreciate an advice concernig: type of Rubber and Suppliers.?

09 October 2017 2,176 0 View

What plasticizers could you recommend for Cellophane film?

07 August 2017 1,370 5 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

What solvent can I used for Paal Knorr reaction between 6-amino hexanoic acid and 2.5 hexanedione?

I am try to make the Paal Knorr reaction between 2.5 hexnedione and 6-amino hexanoic acid, my problem is type of solvent to use, because 6-hexaminohexanoic acid is soluble in water but I am not...

02 March 2021 4,443 2 View

How to polymerize TEOS?

I want to polymerize TEOS on a surface. I know that NH4OH is a preferred catalyst and an alcoholic solvent should be used .But I can not find certain amounts of each material to use. Does any one...

02 March 2021 1,404 6 View

How can extract ciprofloxacin hydrochloride disolve in water er to organic solvent such as dichloromethan or any other solvent?

I need a procedure to extract the ciprofloxacin hydrochloride from aqueous solution by using dichloromethane in detail,. I thank you very much.

01 March 2021 4,306 1 View

How to separate water from glycerol solvent in a solvent recovery vacuum distillation column?

I am currently doing my third year design project. I have been assigned to design a glycerol recovery column in vinyl acetate monomer production. The process unit before the recovery column is an...

01 March 2021 9,525 4 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to make fractions of chloroform extract of plant, using seperating funnel?

28 February 2021 8,466 2 View

Why am i not getting solid after reacting APTES with salicylaldehyde?

The reaction of APTES with salicylaldehyde in ethanol leads to the formation of imine compound yellow solid which is mention in literature, but I am not getting yellow solid I don't know why? when...

28 February 2021 2,955 2 View