Adhesive for carbon and/or glass filaments sustaining -150C + 150C?

We need Adhesive for carbon and/or glass filaments sustaining -150C + 150C? It may be like PolyAmide Imide adhesive or adhesive cured by UV, or any combination of adhesives.

07 August 2018 2,898 5 View

Polyimide based on Diamine R?

Polyimide based on Diamine R? for preparation of thermal-resistant Polyimide powder

05 June 2018 704 2 View

What is more important than success in our Living?

My previous question was: """To be successful in life - what does it mean?""" Almost all the answers to this question were about: "What is the Success? and how to reach the success" - a...

03 April 2018 2,019 96 View

How to remove from the Metal surface the PSA adhesive?

How to remove from the Metal surface the PSA adhesive by using non-aggressive solvents? What type of solvents would you recommend? at what temperature?

03 April 2018 5,489 6 View

What are the best solvents to precipitate Aromatic PolyAmic Acid from its solution in DMF or DMAC?

What are the best solvents to precipitate Aromatic PolyAmic Acid from its solution in DMF or DMAC?

31 December 2017 4,598 2 View

How to obtain a precipitated powder of Poly-Amic Acid based on aromatic diamine and aromatic dianhydride?

How to obtain a precipitated powder of Poly-Amic Acid (PAA) based on aromatic diamine and aromatic dianhydride? It is well known that for several Aromatic Polyimides (PIs) in the course of...

11 December 2017 2,072 2 View

Band assignments for FTIR spectra of Ground Rubber Tire Crumps?

FTIR spectra of GRT are difficult to "read" because of carbon filler. The bands are broad and have of very low intensity. As a whole the contribution of the spectrum of GRT to the total spectrum...

09 October 2017 6,952 6 View

Thermo-resistant Rubber for Gumming Calender Shaft?

We are looking for manufacturer/supplier of Super-Thermo-Resistant Rubber for Gumming Calender Clamping Shaft. We'd greatly appreciate an advice concernig: type of Rubber and Suppliers.?

09 October 2017 2,176 0 View

What plasticizers could you recommend for Cellophane film?

07 August 2017 1,370 5 View

The best method of dissolution of Cellulose ?

What is the easiest method of how to obtain Cellulose films free of ions

07 August 2017 4,884 9 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View