Thermo-resistant Rubber for Gumming Calender Shaft?

Leonid V Vladimirov @Leonid_Vladimirov2

10 October 2017 0 2K Report

We are looking for manufacturer/supplier of Super-Thermo-Resistant Rubber for Gumming Calender Clamping Shaft.

We'd greatly appreciate an advice concernig: type of Rubber and Suppliers.?

Badges
Science topic

Similar topics
Econ
Manufacturing

More Leonid V Vladimirov's questions See All

Binder for reinforced plastics with fluidity temperature 100-120C, prepreg on its base containing >50% carbon filaments and examples of articles made?

Binder for reinforced plastics with fluidity temperature 100-120C, prepreg on its base containing >50% carbon filaments and examples of articles made of it. We seek for prepregs with at least...

07 August 2018 1,232 0 View

Adhesive for carbon and/or glass filaments sustaining -150C + 150C?

We need Adhesive for carbon and/or glass filaments sustaining -150C + 150C? It may be like PolyAmide Imide adhesive or adhesive cured by UV, or any combination of adhesives.

07 August 2018 3,057 5 View

Polyimide based on Diamine R?

Polyimide based on Diamine R? for preparation of thermal-resistant Polyimide powder

05 June 2018 871 2 View

What is more important than success in our Living?

My previous question was: """To be successful in life - what does it mean?""" Almost all the answers to this question were about: "What is the Success? and how to reach the success" - a...

03 April 2018 2,187 96 View

How to remove from the Metal surface the PSA adhesive?

How to remove from the Metal surface the PSA adhesive by using non-aggressive solvents? What type of solvents would you recommend? at what temperature?

03 April 2018 5,711 6 View

What are the best solvents to precipitate Aromatic PolyAmic Acid from its solution in DMF or DMAC?

31 December 2017 4,755 2 View

How to obtain a precipitated powder of Poly-Amic Acid based on aromatic diamine and aromatic dianhydride?

How to obtain a precipitated powder of Poly-Amic Acid (PAA) based on aromatic diamine and aromatic dianhydride? It is well known that for several Aromatic Polyimides (PIs) in the course of...

11 December 2017 2,284 2 View

Band assignments for FTIR spectra of Ground Rubber Tire Crumps?

FTIR spectra of GRT are difficult to "read" because of carbon filler. The bands are broad and have of very low intensity. As a whole the contribution of the spectrum of GRT to the total spectrum...

09 October 2017 7,108 6 View

What plasticizers could you recommend for Cellophane film?

What plasticizers could you recommend for Cellophane. How to plasticize Cellophane - at some stage of film manufacturing ? or via swelling ?

07 August 2017 1,550 5 View

The best method of dissolution of Cellulose ?

What is the easiest method of how to obtain Cellulose films free of ions

07 August 2017 5,049 9 View

How to add viscosity into a hyperelastic material such as Mooney-Rivlin rubber in LS-DYNA?

Hi, I am working on a head FE model and want to try different material types on brain. I read some papers that use Mooney-Rivlin rubber model and wondering if i can add viscosity into it. Is it...

24 July 2024 5,908 0 View

How is surfactant addition calculated?

I want to make 100 ml of MWCNT/distilled water mixture at a volume fraction of % 0.1. MWCNT density is 2100 kg/m3. I will add gum arabic as surfactant. If I add surfactant at a 1:1 ratio, will the...

19 July 2024 8,494 0 View

How to classify 3D Bioprinting as a part of Additive Manufacturing?

Hello, I have a problem in classification of "Additive Manufacturing" techniques. There are several classification for Additive Manufacturing e.g. Powder, Extrusion, Resin etc. Actually, I am OK...

15 July 2024 139 3 View

I need Agile topic for my PHD ? any recommendation ( Safe) ?

Hello All, it has been a while searching for a good topic to Agile, and also i need topic that can do a real impact in agile field? any recomendation ?

07 July 2024 8,450 3 View

What is polymer/chemicals can increase the swelling index of a polymeric film?

Polymeric film such as latex rubber substrate or polymer

01 July 2024 8,343 4 View

What is the basic difference between gum and hydrocolloid?

30 June 2024 4,031 3 View

What role does grain size play in the mechanical properties of nanocrystalline metals and how can this be controlled during the manufacturing process?

In nanocrystalline metals, the size of their crystalline grains affects how strong, ductile, and hard they are. Smaller grains often mean stronger metals but can reduce ductility. Controlling...

28 June 2024 6,925 0 View

What are the engineering applications of polyethylene with waste tire rubber?

When polyethylene, whether high-density or low-density, is mixed with percentages of waste tire rubber, it becomes a new material. Where can it be used?

26 June 2024 3,349 2 View

Is there a specific FTIR figure if epoxy/ polysufide reinforced with Sic?

I have a copolymer if epoxy and rubber reinforced with Sic. I want a standard FTIR figure in transmittance mode.

20 June 2024 6,606 2 View

How to define viscoelasticity in ABAQUS?

I am trying to define the viscoelastic parameters of a rubber material using abaqus, but I don't quite understand how to proceed. I now have stress-strain curves at different temperatures, and...

13 June 2024 3,150 2 View