How to remove from the Metal surface the PSA adhesive by using non-aggressive solvents? What type of solvents would you recommend? at what temperature?
If you want to delaminate, use heat. For cleaning od the polymer adhesive, try acetone, TFA, chloroform.
Dear Andrei:
PSA is not a common polymer-adhesive. The methods you've proposed regretfully do not work
Hi Leonid,
Use alcohol and heat, some alcohols causes denaturation of adhesive.Good luck
Dear Salim:
Thank you for your advice.
And what do you think about using some high-molecular-weight hydrocarbon-oils ? Will them do the job ?
Dear Leonid,
Try High boiling point alcohol, if it is not working try high molecular weight hydrocarbon oils with heating. Good Luck.
Thank you I'll try - following to your advices.
Leonid
Binder for reinforced plastics with fluidity temperature 100-120C, prepreg on its base containing >50% carbon filaments and examples of articles made of it. We seek for prepregs with at least...
07 August 2018 1,232 0 View
We need Adhesive for carbon and/or glass filaments sustaining -150C + 150C? It may be like PolyAmide Imide adhesive or adhesive cured by UV, or any combination of adhesives.
07 August 2018 3,057 5 View
Polyimide based on Diamine R? for preparation of thermal-resistant Polyimide powder
05 June 2018 871 2 View
My previous question was: """To be successful in life - what does it mean?""" Almost all the answers to this question were about: "What is the Success? and how to reach the success" - a...
03 April 2018 2,187 96 View
What are the best solvents to precipitate Aromatic PolyAmic Acid from its solution in DMF or DMAC?
31 December 2017 4,755 2 View
How to obtain a precipitated powder of Poly-Amic Acid (PAA) based on aromatic diamine and aromatic dianhydride? It is well known that for several Aromatic Polyimides (PIs) in the course of...
11 December 2017 2,284 2 View
FTIR spectra of GRT are difficult to "read" because of carbon filler. The bands are broad and have of very low intensity. As a whole the contribution of the spectrum of GRT to the total spectrum...
09 October 2017 7,108 6 View
We are looking for manufacturer/supplier of Super-Thermo-Resistant Rubber for Gumming Calender Clamping Shaft. We'd greatly appreciate an advice concernig: type of Rubber and Suppliers.?
09 October 2017 2,355 0 View
What plasticizers could you recommend for Cellophane. How to plasticize Cellophane - at some stage of film manufacturing ? or via swelling ?
07 August 2017 1,550 5 View
What is the easiest method of how to obtain Cellulose films free of ions
07 August 2017 5,049 9 View
I need to do some experiment with it in liquid form.
07 August 2024 613 3 View
I work on MCF7 cell cell for anticaner purpose and I wa to do drug preperation the drug ( secondary metabolites extracted from Aspergillus) My question which solvent is better with these secodary...
03 August 2024 4,725 2 View
Hello everyone, I need to dissolve stigmasterol for an animal experiment, but it hasn't dissolved in either DMSO or vegetable oil. Can anyone recommend the best solvent for stigmasterol?
01 August 2024 7,504 2 View
Why methanol and sulphuric acid, used in the analysis of polyhydroxyalkanoates (PHA) methyl esters by GC-MS? Additionally, why do we typically use non-polar solvents in GC-MS?
22 July 2024 1,210 2 View
Is it the best optimization ratio based on experiments?
22 July 2024 8,170 0 View
If you don't understand my question let me know
21 July 2024 563 1 View
I used several solvents and measured the absorbency and determined the total phenolic content, but the results were similar after dropping them on the titration curve; What is the reason, please help
17 July 2024 5,151 5 View
Hello everyone, I am facing a consistent issue in my NMR spectra with an unwanted peak appearing at 1.25 ppm. This peak seems to vary with the amount of sample: it becomes more pronounced with...
15 July 2024 9,065 4 View
I synthesised a nanocarrier by conjugation MOF (MIL-100) with folic acid for use in chemotherapy but the samples didn't dissolve completely in aqueous solution or DMSO. Instead, they only...
15 July 2024 2,414 1 View
as of my knowledge z90 is acrylic based sealant adhesive.
09 July 2024 8,660 4 View