Which kind of the MATLAB version is suitable for coupling with ANSYS Maxwell 16?

More Alireza Sahafi's questions See All

How can I get the d-axis and q-axis inductance characteristics?

Hello, I've simulated a reluctance synchronous motor in 2D maxwell and now, I want to get Ld and Lq characteristics. Does anybody know about it?

31 December 2017 9,907 0 View

Is anybody know about controlling of the BLDC motor by single - sensor current?

I've simulated a Four-Switch Three-Phase BLDC motor by single current sensor, but there is a little problem in Simulation results,Can anybody to help me?

06 July 2017 6,149 5 View

Does anybody know about DFIG?

I have simulated a DFIG structure in Matlab,When I run the simulation,a error appears. I,ve attached it here. Please check it.

05 June 2017 2,473 5 View

How can I design a first - order filter for output of the single-phase VSI inverter in Matlab?

Specification of the single-phase VSI inverter: Vdc=400v load= RL R=10 , L=50*e-3 H reference signal=sin wave (50HZ) carrier signal=Triangular signal (500Hz)

11 December 2016 8,745 0 View

How can I find alloy material data sheet?

I need following data sheet (B-H curve): CoFe SiFe (for designing of the motor core) Please help me.

10 November 2016 776 3 View

How can I desgin TSF method for switched reluctance motor torque control? ?

I want to know,How I can implement TSF method,Assuming that switching angles to be as follows: tetaon=0 tetaoff=18 tetac=30

06 July 2016 7,688 4 View

Is anyone know about current control by PWM method?

I want to know how I can simulate a current PWM controller for a switched reluctance motor,I want to simulate it in Mtlab/simulink, Please help me.

06 July 2016 9,427 4 View

What's the dwell angle (teta off - teta on) range for a switched reluctance motor in the rated speed?

I've simulated a 8/6 SRM in Matlab at rated speed and load, I want to know How much should be the dwell angle? (15 degrees or more)

05 June 2016 2,018 2 View

How can I simulate sensorless fuzzy logic method for a switched reluctance motor in simulink\Matlab?

I want to know how can I simulate fuzzy logic controller blocks in simulink?What is the difference between controller blocks?and what is details related to designing these blocks? These are two...

05 June 2016 5,061 1 View

Is anyone know about details of the Switched reluctance motor simulation in the simatlab?

I want to know: 1)To simulation of no-load mode,How much should be the reference current value ( Rated current or less)? ( rated load=25 and rated current=17) 2)What is the limit for motor...

05 June 2016 2,861 4 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

Please, what is the memory consumption of the Matlab function quad tree decomposition procedure [S = qtdecomp(I)] with respect to the input set I?

27 July 2024 5,455 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Seeking MATLAB Code for Differential Evolution in Multilevel Thresholding Image Segmentation ?

Hello, I am a research scholar currently working on a project involving image segmentation, and I am interested in using differential evolution for this purpose . I would greatly appreciate it if...

25 July 2024 9,926 1 View

Swerling Characteristic functions?

Hello!!! I want to implement the Swerling characteristics functions (CF) directly in MATLAB without using its Fourier integral pairs...the Swerling CFs are actually Laplace Transform of the signal...

23 July 2024 4,925 1 View

Radar Detection Probabilities using beta distributed Scattering Cross section?

Currently I need to calculate detection probabilities (PD) from radar cross section (RCS) data. Beta distribution parameters for this RCS data are calculated and will be used in Swerling0...

22 July 2024 868 0 View

How Do Length of Pylon and Rotor Disk Radius Impact Angular Frequency and Torsional Stiffness in Whirl Flutter Analysis for a 2 DOF Propeller System?

Actually, I'm having trouble implementing the plot of the flutter region for the whirl prop system with 2 DOF (Influences of structural damping and propeller—pivot point distance on whirl flutter...

21 July 2024 5,047 2 View