How can I get the d-axis and q-axis inductance characteristics?

Hello, I've simulated a reluctance synchronous motor in 2D maxwell and now, I want to get Ld and Lq characteristics. Does anybody know about it?

31 December 2017 9,783 0 View

Is anybody know about controlling of the BLDC motor by single - sensor current?

I've simulated a Four-Switch Three-Phase BLDC motor by single current sensor, but there is a little problem in Simulation results,Can anybody to help me?

06 July 2017 6,003 5 View

Does anybody know about DFIG?

I have simulated a DFIG structure in Matlab,When I run the simulation,a error appears. I,ve attached it here. Please check it.

05 June 2017 2,383 5 View

Which kind of the MATLAB version is suitable for coupling with ANSYS Maxwell 16?

Is it possible to coupling Matlab 2013 and Maxwell 16?

31 December 2016 2,150 2 View

How can I design a first - order filter for output of the single-phase VSI inverter in Matlab?

11 December 2016 8,661 0 View

How can I find alloy material data sheet?

I need following data sheet (B-H curve): CoFe SiFe (for designing of the motor core) Please help me.

10 November 2016 704 3 View

How can I desgin TSF method for switched reluctance motor torque control? ?

06 July 2016 7,515 4 View

Is anyone know about current control by PWM method?

I want to know how I can simulate a current PWM controller for a switched reluctance motor,I want to simulate it in Mtlab/simulink, Please help me.

06 July 2016 9,332 4 View

What's the dwell angle (teta off - teta on) range for a switched reluctance motor in the rated speed?

I've simulated a 8/6 SRM in Matlab at rated speed and load, I want to know How much should be the dwell angle? (15 degrees or more)

05 June 2016 1,921 2 View

How can I simulate sensorless fuzzy logic method for a switched reluctance motor in simulink\Matlab?

05 June 2016 4,950 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View