How can I get the d-axis and q-axis inductance characteristics?

Hello, I've simulated a reluctance synchronous motor in 2D maxwell and now, I want to get Ld and Lq characteristics. Does anybody know about it?

31 December 2017 9,783 0 View

Is anybody know about controlling of the BLDC motor by single - sensor current?

I've simulated a Four-Switch Three-Phase BLDC motor by single current sensor, but there is a little problem in Simulation results,Can anybody to help me?

06 July 2017 6,003 5 View

Does anybody know about DFIG?

I have simulated a DFIG structure in Matlab,When I run the simulation,a error appears. I,ve attached it here. Please check it.

05 June 2017 2,383 5 View

Which kind of the MATLAB version is suitable for coupling with ANSYS Maxwell 16?

Is it possible to coupling Matlab 2013 and Maxwell 16?

31 December 2016 2,150 2 View

How can I find alloy material data sheet?

I need following data sheet (B-H curve): CoFe SiFe (for designing of the motor core) Please help me.

10 November 2016 704 3 View

How can I desgin TSF method for switched reluctance motor torque control? ?

06 July 2016 7,515 4 View

Is anyone know about current control by PWM method?

I want to know how I can simulate a current PWM controller for a switched reluctance motor,I want to simulate it in Mtlab/simulink, Please help me.

06 July 2016 9,332 4 View

What's the dwell angle (teta off - teta on) range for a switched reluctance motor in the rated speed?

I've simulated a 8/6 SRM in Matlab at rated speed and load, I want to know How much should be the dwell angle? (15 degrees or more)

05 June 2016 1,921 2 View

How can I simulate sensorless fuzzy logic method for a switched reluctance motor in simulink\Matlab?

05 June 2016 4,950 1 View

Is anyone know about details of the Switched reluctance motor simulation in the simatlab?

I want to know: 1)To simulation of no-load mode,How much should be the reference current value ( Rated current or less)? ( rated load=25 and rated current=17) 2)What is the limit for motor...

05 June 2016 2,777 4 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

How to plot the probability paper of Gumbel distribution using R programing?

In R-studio, there are many commands of Gumbel package. Arguments are also different. I`m asking about the alpha parameter of the Copula which must be greater than 1. If this is the one used to...

25 February 2021 5,229 3 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

Please. Could you help be in implementing Fractal Discrete Cosine Transform algorithm in Matlab?

I do need the Matlab code of Fractal Discrete Cosine Transform (FDCT). Can anyone who has already implement this code, help me with the implementation of this transform?

24 February 2021 5,602 2 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

Multi effect distillation modeling in EES?

Dear colleagues If anyone has a model of multi-effect distillation in EES or MATLAB software, please send it to me.

24 February 2021 7,282 1 View

What program can I use to caclulate dipole moment efficiently and without the need of excessive computation?

Hi, I am a third year chemistry undergrad doing my group project in which I need to predict the HPLC retention time of 20 aromatic molecules. to do this we require the chemical properties of these...

24 February 2021 1,384 3 View