How can I get the d-axis and q-axis inductance characteristics?

Hello, I've simulated a reluctance synchronous motor in 2D maxwell and now, I want to get Ld and Lq characteristics. Does anybody know about it?

31 December 2017 9,783 0 View

Is anybody know about controlling of the BLDC motor by single - sensor current?

I've simulated a Four-Switch Three-Phase BLDC motor by single current sensor, but there is a little problem in Simulation results,Can anybody to help me?

06 July 2017 6,003 5 View

Does anybody know about DFIG?

I have simulated a DFIG structure in Matlab,When I run the simulation,a error appears. I,ve attached it here. Please check it.

05 June 2017 2,383 5 View

Which kind of the MATLAB version is suitable for coupling with ANSYS Maxwell 16?

Is it possible to coupling Matlab 2013 and Maxwell 16?

31 December 2016 2,150 2 View

How can I design a first - order filter for output of the single-phase VSI inverter in Matlab?

11 December 2016 8,661 0 View

How can I find alloy material data sheet?

I need following data sheet (B-H curve): CoFe SiFe (for designing of the motor core) Please help me.

10 November 2016 704 3 View

How can I desgin TSF method for switched reluctance motor torque control? ?

06 July 2016 7,515 4 View

What's the dwell angle (teta off - teta on) range for a switched reluctance motor in the rated speed?

I've simulated a 8/6 SRM in Matlab at rated speed and load, I want to know How much should be the dwell angle? (15 degrees or more)

05 June 2016 1,921 2 View

How can I simulate sensorless fuzzy logic method for a switched reluctance motor in simulink\Matlab?

05 June 2016 4,950 1 View

Is anyone know about details of the Switched reluctance motor simulation in the simatlab?

I want to know: 1)To simulation of no-load mode,How much should be the reference current value ( Rated current or less)? ( rated load=25 and rated current=17) 2)What is the limit for motor...

05 June 2016 2,777 4 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Isolates of Hymenoscyphus fraxineus?

Dear Dr. Cai, my name is Simone Prospero and I work in the team of Phytopathology at the Swiss Federal Institute for Forest Snow and Landscape Research (WSL;...

01 March 2021 1,133 1 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

How to interpolate from a time-series database ?

Hi, I am having trouble with a problem, in the field of Optimal Control and the generation of optimal time-series. Let's consider a system, whose dynamics are represented by dx/dt =...

24 February 2021 9,105 2 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View