Does anybody know about DFIG?

More Alireza Sahafi's questions See All

How can I get the d-axis and q-axis inductance characteristics?

Hello, I've simulated a reluctance synchronous motor in 2D maxwell and now, I want to get Ld and Lq characteristics. Does anybody know about it?

31 December 2017 9,907 0 View

Is anybody know about controlling of the BLDC motor by single - sensor current?

I've simulated a Four-Switch Three-Phase BLDC motor by single current sensor, but there is a little problem in Simulation results,Can anybody to help me?

06 July 2017 6,149 5 View

Which kind of the MATLAB version is suitable for coupling with ANSYS Maxwell 16?

Is it possible to coupling Matlab 2013 and Maxwell 16?

31 December 2016 2,269 2 View

How can I design a first - order filter for output of the single-phase VSI inverter in Matlab?

Specification of the single-phase VSI inverter: Vdc=400v load= RL R=10 , L=50*e-3 H reference signal=sin wave (50HZ) carrier signal=Triangular signal (500Hz)

11 December 2016 8,745 0 View

How can I find alloy material data sheet?

I need following data sheet (B-H curve): CoFe SiFe (for designing of the motor core) Please help me.

10 November 2016 776 3 View

How can I desgin TSF method for switched reluctance motor torque control? ?

I want to know,How I can implement TSF method,Assuming that switching angles to be as follows: tetaon=0 tetaoff=18 tetac=30

06 July 2016 7,688 4 View

Is anyone know about current control by PWM method?

I want to know how I can simulate a current PWM controller for a switched reluctance motor,I want to simulate it in Mtlab/simulink, Please help me.

06 July 2016 9,427 4 View

What's the dwell angle (teta off - teta on) range for a switched reluctance motor in the rated speed?

I've simulated a 8/6 SRM in Matlab at rated speed and load, I want to know How much should be the dwell angle? (15 degrees or more)

05 June 2016 2,018 2 View

How can I simulate sensorless fuzzy logic method for a switched reluctance motor in simulink\Matlab?

I want to know how can I simulate fuzzy logic controller blocks in simulink?What is the difference between controller blocks?and what is details related to designing these blocks? These are two...

05 June 2016 5,061 1 View

Is anyone know about details of the Switched reluctance motor simulation in the simatlab?

I want to know: 1)To simulation of no-load mode,How much should be the reference current value ( Rated current or less)? ( rated load=25 and rated current=17) 2)What is the limit for motor...

05 June 2016 2,861 4 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

People weight in Oaxaca Blinder Decomposition on R?

Hello guys! Do you have experience running a Oaxaca-Blinder decomposition on R applying person weights. How do you suggest doing it? I have a variable PERWT which gives more information on how...

04 August 2024 6,033 0 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

When I simulate for S parameters using ADS, I have faced this issue that I have attached. Please anyone clarify me?

...

31 July 2024 1,671 3 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View

How to perform EEG source analysis on each trial of data separately?

Hello Everyone I have a question about structure for connectivity analysis on sources. My goal: preprocess and cut data into trials create headmodels, using template MRI file perform source...

30 July 2024 2,744 1 View

How to add Cr parameter in autodock?

When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!

29 July 2024 488 0 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

Kouider Khaled

hi,

is the porblem still unsolved or what ????

if not here it is ..i solved the problem ...just check it

good luck

Alireza Sahafi

Thank you Mr. Khaled, but this version of program is not supported in my matlab, Please convert it to version 2016 and submit it.

oki .check this and tell me

Thank you so much Mr.Khaled.

Unfortunately, I do not have my own simulation, but I do not remember how difficult this simulation was. Can I ask what was the problem with my simulation?

oki....please see the attached photo....

please do like what i mentioned in the photo

let me know if you have another problem...i'll try to help