What are the most effective parameters to reduce radiated emissions on capacitive touch sensors?

On the pcb board i have added the series resistor in sensor line in different values. But with increasing the value the radiated emission is still high and there are a lot of peaks in some...

09 October 2018 2,835 0 View

Hi, I am adding the series resistor value to the capasitive sensor , but the Radiated emission is increasing at low frequencies. What is the reason?

By adding the resistor value the LPF must increase and high frequencies will eliminate. So we must have lower radiated emission

09 October 2018 357 0 View

Can anybody introduce me a good paper and useful book in the field of Rf/Microwave cancer biosensor?

11 December 2016 5,498 0 View

I need to know the differences between Electromagnetic Simulation Softwares and the comparison between them?

for example the comparison between MEEP and EM EXPLORER softwares.

06 July 2016 1,595 0 View

Which other open source (or, in any case, "free") implementations of FDTD and RCWA are available, and to compare their capabiities?

05 June 2016 6,824 6 View

Describe how a possible circuit based on molecular transistor could be simulated starting from data at the physical level?

molecular transistor

05 June 2016 5,509 1 View

No title

Si Nanowire

05 June 2016 766 0 View

No title

molecular transistor

05 June 2016 9,749 0 View

Can anybody helps me and propose some good thesis in field of nanotechnologies for ICTs?

In field of Biomedical or other fields that related to nanotechnology

05 June 2016 5,377 0 View

In FinFET technology do shorted gate(SG mode) and independent gate (IG mode0 still using and i need some datas about these modes?

FinFET technology

03 April 2016 1,222 0 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View

Is that possible to do an impedance measurement without FRA module?

One of my colleagues said, "the impedance you can measure with the three electrodes and with the specific sequence varying the frequency" Is it possible to configure the potenciostat without the...

21 February 2021 418 2 View

Do you know this error? The experiment was stopped by a potential overload on Vs (auxiliary electrode)?

Hello everyone Do you have any information about this error 'The experiment was stopped by a potential overload on Vs (auxiliary electrode)' in Origamaster software? I tried everything possible,...

19 February 2021 3,152 7 View

Which compound is getting oxidized during bulk electrolysis with TFAA?

The experiment is really simple. When I do a bulk electrolysis with 1% TFAA (ACN solution) to get dihydrogen, what is going to be oxidized? (working electrode graphit, counter electrode platinum,...

18 February 2021 4,430 1 View

Not able to charge-discharge Li-ion coin cell at higher C rate ?

I am working on cathode material. I have made different Li-ion coin cell against Li metal using commercial available cathode materials such as LCO,LMO, LFP and NMC and also with the lab...

18 February 2021 1,450 3 View