What are the most effective parameters to reduce radiated emissions on capacitive touch sensors?

On the pcb board i have added the series resistor in sensor line in different values. But with increasing the value the radiated emission is still high and there are a lot of peaks in some...

09 October 2018 2,835 0 View

Hi, I am adding the series resistor value to the capasitive sensor , but the Radiated emission is increasing at low frequencies. What is the reason?

By adding the resistor value the LPF must increase and high frequencies will eliminate. So we must have lower radiated emission

09 October 2018 357 0 View

Can anybody introduce me a good paper and useful book in the field of Rf/Microwave cancer biosensor?

11 December 2016 5,498 0 View

I need to know the differences between Electromagnetic Simulation Softwares and the comparison between them?

for example the comparison between MEEP and EM EXPLORER softwares.

06 July 2016 1,595 0 View

Which other open source (or, in any case, "free") implementations of FDTD and RCWA are available, and to compare their capabiities?

05 June 2016 6,824 6 View

Describe how a possible circuit based on molecular transistor could be simulated starting from data at the physical level?

molecular transistor

05 June 2016 5,509 1 View

No title

molecular transistor

05 June 2016 9,749 0 View

Can anybody helps me and propose some good thesis in field of nanotechnologies for ICTs?

In field of Biomedical or other fields that related to nanotechnology

05 June 2016 5,377 0 View

In FinFET technology do shorted gate(SG mode) and independent gate (IG mode0 still using and i need some datas about these modes?

FinFET technology

03 April 2016 1,222 0 View

What is Flip-chip technique?

interconnect

01 February 2016 4,488 1 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

How to simultaneously perform multiple biochemical assays?

I am a research scholar working on heavy metal stress on plants. I will be doing biochemical characterisation( protein, carbohydrate, proline, antioxidant enzymes and many more assays) at interval...

01 March 2021 6,999 3 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

How can I selectively dry etch Ti on a polymer substrate?

24 February 2021 5,378 1 View

Why is NH4OH added in heavy metals limit test?

The limit test I'm referring to is USP method II. In this procedure you need to dropwise add 6N of NH4OH to the sample until it the pH is alkali. After that you need to dilute and add HOAc until...

23 February 2021 2,049 3 View

Is this the write procedure for acid digestion of soil for heavy metal analysis using AAS?

How to do acid digestion of soil sample with 3:1 aquaregia in an open vessel?

23 February 2021 3,053 7 View

Can't recognize exact phase and PDF card no of Silicon carbide in XRD?

We have deposited silicon carbide on carbon substrate using one PVD technique. Due to amorphous behavior of SiC at low deposition temperature, we performed heat treatment of those films at...

22 February 2021 2,072 3 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

Amorphous silica XRD peak at around 10 degree?

21 February 2021 3,417 5 View