Which is a good and easy software to make 3D model ?

More Anil Kumar Pal's questions See All

Where can I get CIE 1976 chromaticity space software?

I want to plot the color co-ordinates obtained from florescence spectrum. Where can I get CIE 1976 chromaticity space software. [ Rather than ORIGIN software where the templets of 1931 and 1976...

31 December 2016 8,910 7 View

Free software for 3D model?

I want to make a model for my work. I want to know a free and easy software so that I can learn myself in a short time. Any one know, do suggest. I have attached a model image. Thanks you.

10 November 2015 4,837 13 View

Without recording Absorbance spectra (A), can we use Beer's law to calculate A from Transmittance spectra (T)?

I have T of Ag/Glass film recorded by UV-Vis spectrometer. Can I use Beer's law, A=Log(1/T) to find out A? Whether this will be correct without recording A experimentally?

03 April 2015 5,563 8 View

How can I calculate n and k value of Ag films on glass substrate?

I have %T and %R spectra. The film is not opaque. Please give some references for this.

01 February 2015 3,524 7 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Binder for ZnO nanoparticles in graphite paste electrode?

I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?

03 August 2024 4,624 3 View