Where to define 2G, 3G and other G forces ?

Prabhu Prakash @Prabhu_Prakash

02 February 2018 0 7K Report

HI All,

We have crossed the G (gravity) force during FEA analysis.

Is there any specific conditions for the application of 2G and 3G loads and even higher.

Where should we apply 2G, 3G and higher values.

Badges
Science topic

More Prabhu Prakash's questions See All

How to add cam and follower contacts in ANSYS RBD ?

Hi all, i have to make an RBD analysis for the cam and follower assembly. I have setup the model and applied the joints accoringly (body to body and body to ground). But I am struggling in...

31 December 2018 9,308 3 View

How to merge opposite trias in ansys workbench ?

Dear all, is there any possible ways to avoid/merge the opposite trias in Ansys workbench. Opposite trias in my model is shown in the attached image. I was working in hyper mesh. In that tool, it...

11 December 2018 7,796 4 View

Sensors for measuring oxygen and carbon di-oxide ?

Dear all, I am doing a project in hydrophonics. I am struck in selecting sensors for my work. Can you please suggest me sensors for the following.. 1. Measuring the amount of oxygen in water. 2....

10 November 2018 8,396 4 View

Equation to find the co-ordinate of point on a circle ?

Hi all, Consider a plane with circle on it. The circle and the plane have same vector/normal (i,j,k). The inputs i have are Radius of the circle (4mm), co-ordinate of the circle center point on...

07 August 2018 1,457 5 View

How to get the length of multiple RBE2 elements at a time ?

I have created an assembly model with around 200 RBE2 connections. My requirement is to measure the length of all the RBE2 element and save it as text or excel file. The number of RBE2 elements...

06 July 2018 3,728 3 View

How to create node with particular node number ?

Hi All, I have meshed a sheet metal part using hyper mesh. I need to take the output in particular co-ordinates. So, I have renumbered all the nodes from 1000. Now using *createnode (x) (y) (z) ,...

04 May 2018 9,634 2 View

How to find the Software used?

Hi all, I am converting a Solid Works / Creo / CATIA file into a STEP or IGES file. Is it possible to trace the history of the file. Is it possible to get the details from the STEP file - reg., on...

05 June 2017 579 2 View

SPH analysis - can we perform it in ANSYS ?

Hi all, Smoothed-particle hydrodynamics I have been assigned a task to conduct SPH based analysis for a sheet metal part. Can anyone help me out in selecting an apt software to perform the analysis.

11 December 2016 1,689 4 View

What kind of contact type should I apply in ANSYS workbench?

Hi all, I have to analyze a structure which have welded and non welded contacts. For welded portions, i have assigned bonded contact type. For the non welded portions, what type of contact should...

11 December 2015 7,141 4 View

Does teaching of CAD / CAE softwares comes under Engineering Services ?

Generally Engineering Services refers to engineering works related to industries. I have a doubt, that, does teaching CAD / CAE softwares to college students come under Engineering Services.

05 June 2015 6,462 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View