I can't find the Fluent 2020R2 "normalization" option. Pic 1 (screenshot) is from a guide that a Professor sent me.
Good topic
Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?
06 August 2024 980 5 View
Hello everyone! I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...
05 August 2024 5,729 2 View
Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...
03 August 2024 5,358 0 View
need to open an account to upload my published papers
01 August 2024 9,255 1 View
All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.
01 August 2024 589 4 View
I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...
01 August 2024 9,227 1 View
Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...
30 July 2024 9,824 2 View
N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.
30 July 2024 7,233 4 View
Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...
30 July 2024 906 2 View
Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...
29 July 2024 7,198 9 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,182 8 View
hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.
03 July 2024 5,418 4 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View
I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...
26 June 2024 2,358 0 View
EMMS - Energy Minimization Multi-Scale
18 June 2024 5,857 2 View
Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...
14 June 2024 6,480 0 View
What does it mean meshed wall and shell conduction with or without run-out method use to meshing copper tube in Ansys fluent?
07 June 2024 9,030 3 View
Assuming I have three domains (three cubes e.g.) placed side by side, the electrical potential equation ( which I am specifying as a User Defined Scalar (UDS)) is solved in the left and right...
05 June 2024 4,153 0 View