What type of part to be printed to check accuracy of fused deposition modeling printer?

More Pooja Rantnakant Padyal's questions See All

Is there any good online workshop on advanced DEA models?

OR ANY study material with step by step analysis & its interpretation using the software?

01 January 2021 993 1 View

How do I get ConsistencyDupSNP.sh file required for genotype consistency quality control step of genotyping data obtained from GSA 24 v2.0 ?

Genotyping data is from Illumina Global screening array 24 v 2.0 and ConsistencyDupSNP.sh file contains list of pair of duplicated SNPs in GSA24 v 2.0.

18 December 2020 1,966 3 View

Can I get some important resources to analyse Photoluminescence Spectra?

I am trying to figure out what information can I get with the help of PL spectra and how to analyse it? How to do the defect analysis, if I am using two different material for thin film how will...

14 November 2020 2,453 6 View

Hazard value for malaria survival graph??

In an experiment untreated infected mice and infected treated mice observed. I recorded my data in terms of survived mice to 28 days in each group. How to calculate hazard value for treatment vs...

06 November 2020 5,548 1 View

How to analyze nominal/ordinal data in cases where you are testing multiple drugs/ infection against common risk factors?

chi-square or Fisher exact test I have a statistical question about chi-square and/or Fisher exact test. I have a cohort data studying the cause of infection in BRD with variables such as age,...

28 October 2020 2,589 1 View

What tips to follow while renaming a research paper in your repo for easier and quicker retrieval later during Ph.D research?

We often download tons of research paper related to our Ph.D research domain in their default filename format. After few days, recollecting and finding a particular paper becomes difficult. Any...

12 October 2020 2,425 3 View

Why will a very intense peak in XRD even beyond instrument detection limits, will appear in a Sample?

I recently submitted my samples in two different labs, I am getting three very intense peak in between 69-70 (2theta degrees); I want to know what could be the possible reason behind, is it normal...

13 September 2020 2,064 4 View

What kind of data ICPOES Perkin Elmer Optima 5300V ICP-OES provide with?

I recently submitted my samples to a laboratory for ICPOES, I am only provided with Standard Deviation and Mean data of one element out of two. I want to know if there is any spectra that is...

21 August 2020 2,428 2 View

How to check virulence of Fusarium oxysporum TR4?

Please add your suggestions for the following questions: 1. Can anyone suggest me the meaning of "fungus has lost its virulence"? 2. If I am able to observe micro and macroconidia under...

27 July 2020 1,099 1 View

Why do drug resistant cell lines show different morphology?

I have a HNSCC cell line resistant to a drug (2 different clones) showing different morphology than the parental cell line. Attached are phase contrast images of these cells. There are black dot...

15 July 2020 1,881 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

I am looking for a simple software program to model 3D chemical bonds. The purpose is to generate high-quality graphical abstracts. Any suggestion?

Hello everyone: I am looking for a simple software program to model chemical bonds. The purpose is to generate a high-quality graphical abstract for a top leading journal in the field of...

23 February 2021 8,012 3 View

Which programs are to be used to register 2D image onto a 3D image data set?

I am trying to register a light micrograph onto a 3D CT data set, as I want to extract the corresponding image from the CT data set. Is there any software or program can do this accurately? I am...

21 February 2021 8,220 3 View

What is the better software for approximation of 3D surface with equations?

I have a massive of x, y, z coordinates of 2D surface in 3D space, which builded in Ansys HFSS or AutoCAD. How can I get the analitical aproximation of this surface by formulas?

21 February 2021 3,444 7 View

How can I obtain Reaction Forces in ABAQUS?

I am trying to simulate a simplified version of a beam resting on 10 points using Abaqus. The solutions I want to obtain are the Reaction Forces in each resting point or area when applying a...

21 February 2021 3,075 2 View

How to convert 2D stack images to 3D to obtain surface area of nucleus?

I have 15 slices of the nucleus at different z-heights from confocal imaging. I would like to use these slices to reconstruct the 3D nucleus and ultimately estimate the surface area of the...

20 February 2021 6,967 1 View

How to get the vector of a specific vibration mode in phonon dispersion?

For example, I have this phonon dispersion(Fig. 1), and now I would like get vector of atoms which describes TA1 in P. I know v_sim can show vibrational animation of specific mode, but I do not...

20 February 2021 4,332 4 View

Has anyone used deep learning for 2D/3D REGISTRATION ?

I am a Master student in Biomedical (Bio-electrical) Engineering and work on " 2D-3D registration ( CT and X-Ray) as my thesis. I created DRR from CT and want use CNN( Convolutional Neural...

19 February 2021 6,354 3 View

How compare between threshold value and mean gray grayscale image in python ?

Iam working on signature image and I need to find geometric features like(slant,pressure,size,baseline)

15 February 2021 7,565 2 View

PV system design. 3d modelling and Analysis?

I have been looking for a good cost-effective tool for 3D modelling a glass-glass solar module system. I was initially considering Skelion as a tool but it does not look very promising, a bit...

13 February 2021 8,126 1 View

Vijaya sankar kn

You can print rectangle or square boxes of different heights.

Ankit Nayak

The accuracy of additive manufacturing can be check by measuring the volumetric error of the printed part, and volumetric error depends on the part orientation, slice height and part geometry. For more detail you should refer these articles.

Conference Paper Volumetric Error Control in Layered Manufacturing

Article A Study of Build Edge Profile for Prediction of Surface Roug...