Which software use to i make this graph quickly and also make more dimensions of this graph( i mean adding vertices or lines in this graph)?

More Awais Iqbal's questions See All

Is there an English Translation of the Carl Moller text: ZUR VERGLEICHENDEN ANATOMIE DER SILURIDEN?

I recently came across an anatomy text by Carl Moller that was published in 1915 but it is in German or Dutch neither of which I can understand. I would like to know if there is an English...

10 August 2024 4,347 1 View

What publications should I target as a psychology masters student in the UK?

I am writing a paper as a part of my course. I am new in London and was wondering that what publications should look upto?

21 July 2024 3,538 1 View

I have two problems: 1) the enzyme is not immobilizing efficiently into the MOF material.. 2) the MOF itself has peak on 400nm by using p-NPA test.?

I am working on carbonic anhydrase immobilization into MOFs. I am facing problems with low enzyme loading.. The other issue is that when using p-NPA activity test to detect the activity of the...

20 July 2024 1,440 3 View

What analysis to use for an dependent variable with repeated measures and a independent variable only measured once?

Hi all, I am trying to use mixed effect model to analyze my data, which including a baseline measurement for my exposure (A), and repeated measurements for the outcome (B). I do have some...

17 July 2024 8,682 3 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

I need to know the required time for VDF heating with water for 50-80°C for PVDF Polymerization in ?

i need to know the required time

15 July 2024 4,796 2 View

What analyzes do you use to compare biodiversity in a square, at two different times?

e.g. moment one: square in its normal state moment two: square after cutting large trees and replacing them with dwarf trees.

12 July 2024 8,258 5 View

Authorship for data analysis?

I participated in 2 research projects in which I was responsible for part of data analysis and figures production. Also, I spent hours trying a new statistical approach -for me- to implement in...

10 July 2024 1,226 5 View

Can anyone confirm the bench mark value of Effect Size (ƒ2)?

Effect sizes are evaluated as small (0.02), medium (0.15) or large (0.35) respectively, according to Cohen (1988). OR According to Cohen (1988; 2019), the f2 values of 0.10 represent small effect;...

29 June 2024 830 1 View

How to converge PEMFC in Ansys Fluent?

I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...

26 June 2024 2,358 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,070 3 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

Entropy measure and QSPR modeling in Graph Theor. How to construct the table for lengthy equation?

The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...

30 July 2024 3,126 0 View

There is possible way to calculate experimental DOS from the UPS spectrum of the material. How to calculate the DOS from UPS?

Here, I have attached the UPS graph. I'm trying to calculate the DOS/DOVS from the UPS.

29 July 2024 4,971 1 View

CAD File of human's & rat's respiratory airways ?

Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...

29 July 2024 1,092 2 View

Critique Calculaltion in Topological Indices and QSPR Modeling?

The first step is to analyze a 2D molecular graph and implement partitioning techniques to calculate the topological indices. Secondly impose statically tools to generate QSPR model, may or may...

24 July 2024 9,644 1 View

How to do calculation of Louvain methods calculation for excel sheet and and is there any software available?

The Louvain method – named after the University of Louvain where Blondel et al. developed the algorithm – finds communities by optimizing modularity locally for every node’s neighborhood, then...

23 July 2024 6,659 0 View

Cell optimization in 1D Nanotubes?

Dear All, I use Quantum Espresso. I want to optimize the structure of the carbon nanotube using the vc-relax. I got confused about how to fix cell_dofree here. For 3D, cell_dofree = 'all' or...

22 July 2024 5,708 0 View