What steps do I need to take to conduct a power analysis when using Hayes' PROCESS model number 58?

08 March 2020 1 5K Report

This is a moderated mediation model, and I have no idea where to start to determine a sample size or how to conduct a power analysis.

Jack Cincotta

Thank you Haroon R Abbu

Badges
Science topic

More Jack Cincotta's questions See All

How to make ribbon protein structure picture?

Hello, everyone. I'm in trouble... hoping someone can get me out How is the protein diagram of this ribbon made? Especially the flexible corners of these rounded corners. Thank you!

20 June 2024 2,796 2 View

What are skewness/kurtosis sampling distributions?

For the skewness and kurtosis coefficients sampling distributions, are they assumed to be normal or some other distribution shape?

15 May 2024 6,037 0 View

How to process CG simulation for protein containing disulfide bonds?

Hello, everyone I am simulating a single chain protein containing disulfide bonds. Force filed of Corase Grained simulation is Martini 2.2, it was run in gromacs2020 in Windows system. I wonder...

07 May 2024 4,213 2 View

I need a reading related to adherence of data protection policies?

challenges affecting adherence as per data protection policies is concerned

21 April 2024 2,654 1 View

How does pymol software render the same structure as ChimeraX?

Hello, everyone! Can somebody help me? I want to draw the protein structure in pymol with this rendering effect, how should I set the light?

17 April 2024 3,378 1 View

Poor DAPI staining in fixed brain sections?

I have a question about some weird nuclei I see while imaging. I'm sorry if this isn't the best place to write it! One image has bad, "shattered"-looking nuclei from dentate gyrus. The other...

08 April 2024 7,534 2 View

How to explain the higher intramolecular FRET efficiency of flexible structures?

The BFP and GFP are connected by a flexible linker and FRET is more higher.

18 March 2024 5,035 4 View

Is there a database for European Carabidae traits?

I am looking for a database of European Carabidae traits - average body length, wing morphology, habitat preference, etc. I have come across Carabids.org but it seems to be down. Is anyone aware...

17 December 2023 4,079 9 View

Request for Literatures ?

Use a model trained in basic theory to recognize the type, location and size of defects. Please help with such papers or articles, web sites. Thank you!

01 December 2023 7,000 0 View

How to formulate acrylic adhesive to bond two plastics?

Common acrylic adhesive, such as two part acrylic adhesive, can bond two metal material very tightly, but can not bond two plastics. Is there any solution to improve the adhesion ability between...

31 October 2023 5,786 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Which distribution type should I use when calculating the average particle size from TEM image? and how to calculate the error ?

average particle size calculation from TEM

04 August 2024 2,921 1 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View