Common acrylic adhesive, such as two part acrylic adhesive, can bond two metal material very tightly, but can not bond two plastics. Is there any solution to improve the adhesion ability between two plastics?
Try using pressure sensitive adhesives to bond two plastics. They do pretty good job.
Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?
06 August 2024 980 5 View
Hello everyone! I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...
05 August 2024 5,729 2 View
Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...
03 August 2024 5,358 0 View
need to open an account to upload my published papers
01 August 2024 9,255 1 View
All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.
01 August 2024 589 4 View
I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...
01 August 2024 9,227 1 View
Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...
30 July 2024 9,824 2 View
N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.
30 July 2024 7,233 4 View
Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...
30 July 2024 906 2 View
Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...
29 July 2024 7,198 9 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
Hi all, my experimental XPS results shown that my C3N5 sample consists of N-H bond, hence in this case I should incorporate the N-H bond into my DFT modelling. However, I do notice several papers...
07 August 2024 8,414 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I aim to be as skeptical as possible regarding whether a pair of orthologous genes results in the same phenotype in their different but related bacterial organisms under similar environmental...
05 August 2024 6,787 4 View
Hello, dear colleagues, I would like your help in finding a reference that provides an average water savings due to plastic recycling compared to the consumption of virgin materials, preferably...
29 July 2024 4,630 0 View
If the pairs are similar, will it reduce the adhesion due to electric charges?
29 July 2024 3,185 2 View
The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.
23 July 2024 3,205 0 View
I’m doing cell-surface biotinylation with HEK293 cells and after all the washing and biotin incubation steps (washing with PBS ph8, neutralizing unreacted biotin with 40mM Tris ph8) many of my...
23 July 2024 4,740 3 View
The adsorbate is Arsenic and the adsorbent is a soil
18 July 2024 332 8 View
Hello everyone, I am currently pursuing a PhD in Environmental Engineering with a focus on microplastic studies. My background is in Civil Engineering, and I am relatively new to working with...
18 July 2024 7,258 3 View