There is a lot of software have been using by researcher for process modeling, but what is the best one?
What kind of process do you wish to model? Chemical? organic? Electrolytes? Wastewater? Water?
Also, are you looking for steady-state or dynamic?
Cost no object?
Thank you for your answer, the process I want to modeling is electro discharge machining process
Regards
If you want to model a kind of workflow you can easiliy use Bizagi.
I really recommend the usage of Bizagi
Thank you Johnny
Regards,Azzam
Do you think that the number of visitors to the university's website increases its international classification?
01 February 2018 8,736 25 View
What are the most important factors that increase the classification of universities?
01 February 2018 9,412 40 View
Why is low back pain so common in people? Please if some one give me the biomechanical reasons?
01 February 2018 6,368 9 View
How many hours does the sun shine in your country? How much is the utilization of solar energy?
31 December 2017 5,464 36 View
Is the process of reviewing a research submitted to a conference different from presenting it to a Journal
10 November 2017 6,103 13 View
What are the main reasons, which makes reviewer reject search
10 November 2017 5,858 9 View
What is the shape-memory alloys?
09 October 2017 9,111 4 View
What is the latest definition of atomic orbitals?
08 September 2017 6,850 2 View
I need lot of time to prepare a lecture and what about you?
08 September 2017 3,216 2 View
I am pleased with your opinions
08 September 2017 4,255 32 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Hello experts, Does anyone know any free software about retention index prediction ?
08 August 2024 7,403 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View