Kindly give some suggestions and references related to it.
Just read the following article and it should give you the answer you are looking for
Dear, Following paper may help you
Article Chemical Composition and Larvicidal Activities of the Himala...
Respected Sir,
Thanks for sharing this article. This article is really helpful but I have read this article already and looking for another references related to it. If you have more references related to it, Kindly share them.
Thankds and best regards.
Respected Sir, As we know, the ceramics are brittle in nature, if we add polymer and ceramics in piezo ceramics, then the material behaves as flexible. What is the main reason behind it? Kindly...
01 February 2019 2,263 4 View
Dear Sir, kindly give your valuable suggestion for the mandatory instruments requirements for the Essential Oil Testing laboratory
11 December 2018 5,978 2 View
Respected Sir, if we have the steam distilled essential oil and we would like to extract the abosutes from it, what should be the exact method of extraction and what are the various factors that...
11 December 2018 3,771 3 View
Respected Sir, If we are cleaning the boiler tubes and shell by boiling out method, which one chemical or acid is best suitable? What quantity of acid should be mixed with water solution for...
10 November 2018 6,567 0 View
As we know the GCMS (Gas Chromatography Mass Spectoscopy) is genrally used, but i am interested to know the latest techniques to measure the chemical constituents of natural products and essential...
10 November 2018 873 4 View
Respected Sir, If someone has PDF version of the above mentioned book. Kindly forward it.
08 September 2018 6,341 0 View
This question is related to ANFIS modeling. Kindly give your suggestions.
05 June 2018 1,534 8 View
on what basis the no. of epochs are selected? is there any influence of no. of epochs on output results? kindly give your suggestions.
05 June 2018 9,766 3 View
What are the various controllable parameters? Standard Procedure to produce the Al-Li alloys for industrial application. Kindly suggest me some references related to the processing of AL-Li alloy.
05 June 2018 7,255 2 View
Kindly give your suggestion.
04 May 2018 6,798 4 View
Dear all, Does anybody have a pdf of this paper? Wood, G.R. and Beeston, J.W., 1986. A late Permian lycopod cone Skilliostrobus sp. cf. S. australis Ash 1979 from Queensland. Geological Survey of...
07 August 2024 4,857 2 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...
06 August 2024 977 1 View
Hello everyone, I need to dissolve stigmasterol for an animal experiment, but it hasn't dissolved in either DMSO or vegetable oil. Can anyone recommend the best solvent for stigmasterol?
01 August 2024 7,504 2 View
Hi all, may I ask you for advice about treating monolayer culture cell line with essential oil. Due to the hydrophobic character of the oil, I am concerning how can it equally affect to all the...
31 July 2024 5,301 2 View
Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...
21 July 2024 1,680 2 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...
11 July 2024 5,380 0 View
Hello everyone, I am trying to encapsulate an essential oil in the liposomes using the heating method and encountering some issues. I am following the protocol described below, but my solution...
10 July 2024 4,083 3 View
What will be the pressure in Iron Iron-Carbide diagram? It is at atmospheric pressure?
05 July 2024 1,891 0 View