What is the reason of pressure drop of C2+ stream (e.g. C2, C3, C4 etc.) in underground pipeline when upstream and downstream of pipe is isolated?

Yaser Rasti Khodaverdiloo @Yaser-Rasti-Khodaverdiloo

24 August 2022 0 9K Report

pressure and temperature of pipeline in normal condition is 32 C and 90 barg.

C2+ stream is liquid when pipeline is in service.

Badges
Science topic

More Yaser Rasti Khodaverdiloo's questions See All

How to import Ls-Dyna results to Abaqus visualization?

A model has been analyzed in Ls-Dyna software. How can the results be imported into Abaqus for further analysis?

25 October 2023 5,974 0 View

How can I put the rod of MR damper at mid-stroke length?

Dear all, I am interested in hearing about someone's experience testing a large-scale structure using MR dampers. How can we adjust the stroke length of the MR damper so that the rod of the...

27 September 2023 1,598 0 View

How can define imperfection's equation in Abaqus?

There are several methods to consider the imperfection of the structure like the eigenvalue buckling mode, nonlinear buckling mode and weld depressions. But how to define imperfection as an...

02 June 2023 175 5 View

Inquiry for academic research?

This is a questionnaire for academic research in the hotel industry. I really appreciate your time if you fill out this form: https://forms.gle/fqFuHMk3a161FHNJ7

29 April 2023 5,027 0 View

Identify Natural frequency of a pipe using sine sweep?

Hi experts. I would like to use sine sweep of 0-10KHz to excite a 2" pipe with two supports and measure it's response using a single axis accelerometer. Every time i repeat the experiment, I get...

06 February 2023 9,595 0 View

What are the most effective methods for encouraging immigrant people from Eastern cultures to seek mental health care?

immigrant people from Eastern cultures and seeking mental health care

09 July 2022 5,167 4 View

During times of war and conflict, are social workers more likely to suffer from professional burnout than others?

12 June 2022 8,206 4 View

How does SWAT model calculates recharge for each time step?

In the SWAT documentation 2:4.2.1 Recharge, it was mentioned that the amount of recharge entering the aquifers on day i (mm H2O) is: w rchrg,1 = (1 - exp[-1/delta]).wseep + exp...

19 March 2022 8,004 0 View

How do you use 2-NBDG to measure glucose uptake in INS-1 cells? here is my protocol?

I want to know if there is a protocol to do this assay in INS-1 cell line and if mine is correct. Day 1 1) Seed (150,000 cells) in 24 well plate. 2) Leave in the incubator overnight to allow cells...

15 September 2021 6,327 0 View

Can we dissolve our ethyl acetate crude extract in water and then fractionate it with MeOH/DCM by using Silica gel column chromatography?

Our ethyl acetate crude extract is not completely soluble in MeOH. I want to Know can we dissolve it in water and then fractionate it with MeOH/DCM system by using Silica gel column...

11 September 2021 5,389 8 View

I came across oscillations in a pressure profile for a pipeline flow along the axis of a cylinder, how do I prove that these are not numerical err?

In terms of CFD, we often analyze the stability of the error using Von-Neumann analysis, especially for FDM based problems. Should we follow the same approach for a compressible fluid flow using FVM ?

13 July 2024 6,296 5 View

Need a reference on pig residual analysis report and the parameters containing in it, for an oil and gas pipeline industry. Has anybody done it?

Pigging is basically a cleansing process followed in all pipeline industries after the product has been delivered. There are many types of pigs that are inserted inside the pipeline for this...

27 June 2024 1,221 1 View

An error occurs when preparing ligands in Discovery Studio?

Hello, I am experiencing an error while using Discovery Studio and would like to ask for your assistance in identifying the cause. The details of the error are as follows: [ 22-May-2024 14:59:14...

21 May 2024 4,980 0 View

Nusselt number in ansys fluent?

Hello everyone I wanna calculate the nusselt number in ansys fluent for a triple pipe geometry, and i'm not sure about the right way to do that. I f someone know the correct steps to do. Thanks in...

28 April 2024 1,280 2 View

Can CEL method be used for FSI?

I want to simulate flow structure interactions for a fluid flowing through a pipe without any other factors like gravity. Is that possible? I've been looking at CEL resources and the only thing I...

24 April 2024 1,591 0 View

How to simulate Wall shear stress in COMSOL?

Water flows in a 2D pipe, I am able to prepare a simple simulation resulting in the velocity and pressure across the pipe. But I am interested to simulate the Wall shear stress generated by the...

22 April 2024 8,537 5 View

Open channel hydraulics inside pipes, transient regime?

Someone has a computer program, algorithm or spreadsheet to solve problems of transients on a water flow in open channel regime through a circular section (flowing inside a pipe with free surface)?

10 April 2024 9,477 2 View

How can metals and polymers be separated quickly in a flexible pipe used in the oil and gas industry?

In subsea decommissioning projects, the time it takes to separate materials from a flexible pipe for recycling is important for the quality of the operation. So, what machines and strategies can...

09 April 2024 3,241 0 View

Trying to draw a pipe bend angle other than 90 degree in abaqus 2017 .How can it be done ?

There is no video on youtube that is helping me regarding this issue.Which of following icon in the attached screenshot can help me with it ?

01 April 2024 9,418 0 View

In abaqus 2017 ,my simulation job runs but it is not showing the 75% average von mises stress for any kind of time frame.Can anyone help with it ?

1.Fixed boundary condition at both end of the pipe elbow. 2.Pressure applied is 30 Mpa. 3.Hex ,sweep mesh applied.

18 March 2024 5,935 2 View