RDF calculation of water inside the Carbon nanotubes?

I am trying to calculate the rdf of water molecules present inside the Carbon nanotube. I tried to do the indexing first using gromacs tool gmx selection. But when it comes to calculating rdf, I...

17 February 2021 1,066 3 View

Correlation plot between Gene of Interest and miRNA?

Please suggest portals to retrieve normalized-quantile expressions of micro-RNAs (in RPM).My aim is to construct a correlation plot between the gene of interest and microRNA. I searched in human...

28 October 2020 6,398 3 View

Hello Can anyone suggest a good way of inducing oxidative stress in mice to exhibit proteinurea phenotype in the mice?

Hello Can anyone suggest a good way of inducing oxidative stress in mice to exhibit proteinurea phenotype in the mice or a good method to induce oxidative stress in the mice to study kidney...

26 July 2020 2,999 3 View

What is the relation between lattice parameters and particle size in manganites??

The change in particle size is resulting in change in unit cell lattice paramaters in manganites. Please explain it in terms of crystallography and why is it so.

28 February 2018 1,590 3 View

How can we interpret LC MS data?

I have TIC, EIC and MS data. How to create a library of compound in my plant extract?

21 December 2017 1,418 4 View

Single cell sort of adherent and suspension cells does not yield similar results. Any suggestions?

I am expressing GPCR in CHO cells, in suspension and adherent format. But when single sorting the cells using FACS Aria, i have obtained clones for the suspension format, but the adherent format...

26 September 2016 1,840 3 View

Can anyone help me explain what a hazard ratio of 20 means? Is it acceptable to have large HR values?

15 May 2016 8,894 5 View

How to remove high intensity pixels with other low intensity neighboring pixels in colored image?

10 April 2016 8,454 5 View

What is the minimum amount of papain (23500 Da) that I can see in the SDS PAGE gel?

I am performing reaction between iodoacetyl-PEG-biotin (linker) and papain. Thiol group of papain reacts with the linker to form a thioester bond. then I use streptavidin beads to fish out papain...

28 December 2015 4,814 3 View

Setting up a lab for human DNA extraction?

I am trying to set up our lab for human DNA extraction from brain tissue and CSF. Any suggestions on how to go about setting up a clean room to prevent any external contamination from bacteria,...

03 September 2015 4,581 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View