Trying to draw a pipe bend angle other than 90 degree in abaqus 2017 .How can it be done ?

02 April 2024 0 9K Report

There is no video on youtube that is helping me regarding this issue.Which of following icon in the attached screenshot can help me with it ?

Badges
Science topic

Similar topics
Papers

More Anupama Paul Nedhi's questions See All

Von mises stress not showing for (key in label ) node,after selecting probe values?

The job runs(shows von mises stress 75% to the highest 363.9 Mpa) upto the yield strength (361 Mpa) although it has a ultimate strength (469.29 Mpa)specified. Whenever i try to take some data of...

05 April 2024 6,613 0 View

In abaqus 2017 ,my simulation job runs but it is not showing the 75% average von mises stress for any kind of time frame.Can anyone help with it ?

1.Fixed boundary condition at both end of the pipe elbow. 2.Pressure applied is 30 Mpa. 3.Hex ,sweep mesh applied.

18 March 2024 5,935 2 View

Could anyone recommend materials that have been successfully used to mimic the mechanical properties of bone and neural tissue scaffold?

Hello ResearchGate Community, I am currently working on my final year undergraduate project, which involves the compression testing of tissue scaffolds, specifically focusing on neural and bone...

02 March 2024 4,600 1 View

Optical and acoustic mode in FMR ?

We have observed in literature regarding the optical mode and acoustic mode in FMR spectra. How to identify which one is acoustic and which one is optical? Kindly clarify.

07 June 2023 3,986 3 View

Other than extract method and seeding cells on scaffolds, is there any other methods that can be followed to perform MTT assay?

I have been working with a ceramic based scaffold, and it is to be determined for cell viability, for which I have chosen MTT assay. Although I have tried seeding cells onto the scaffold or taking...

19 January 2023 1,564 4 View

Can I separate monomers and oligomers from Polymethyl acrylate which was produced via convensional heating method?

We dissolve PMA in acetone and precipitate in ethanol?Is it correct method?Instead of ethanol can I use methanol?

16 October 2022 146 1 View

Sparse Matrix Multiplication can be used in both distributed system as well as parallel system?

could anyone clarify that whether can we use Sparse matrix multiplication in parallel distributed system or is it restricted only to Distributed system? If so pls help me with algorithm

02 July 2022 8,619 2 View

Facing problem in UV curing. Why is UV curing not happening even at the desired concentration and wavelength?

Good day researchers! I have been trying to methacrylate and proceed further by UV curing. As per literature, 0.5-1% (w/v) 2-hydroxy-1-[4-(2- hydroxyethoxy)phenyl]-2-methyl-1-propanone (Irgacure...

11 December 2021 7,241 2 View

Hello everyone , hope you all are doing well. can anyone please suggest me a protocol to make a thiol containing myatansinoid to a thiol free ?

I want to make a thiol containing myatansinoid or DM1 compound into thiol free for conjugation process without diminishing it's cytotoxic potential.

14 November 2021 340 2 View

How to prepare 50 mM potassium phosphate (KPi)/50 mM sodium chloride (NaCl)/2 mM ethylenediaminetetraacetic acid (EDTA), pH 6.5 buffer solution?

Can anyone guide me how could I prepare this buffer? Should I first prepare 50mM potassium phosphate then 2 mM ethylenediaminetetraacetic acid (EDTA) .Then I should mix them and pH should...

13 October 2021 1,647 1 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,829 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,027 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 452 3 View

How to draw the five chelate rings of [Co(EDTA)]- on this picture?

Is this circle one of the rings?

03 August 2024 5,987 0 View

How to make overlapping p-h diagram in EES?

I want to draw ph diagram using Engineering equation solver EES for refrigerant R134a and R1234fy and some other. I don't know how to draw the multiple ph diagram on same dome or overlapping to...

30 July 2024 647 7 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,061 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,571 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 645 2 View

Abaqus 2023 - How to know how many elements have been deleted during a simulation ?

Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...

17 July 2024 1,501 1 View