What is the minimum and optimal hardware requirement for running CAMx?

Muntaseer Ibn Azkar @Muntaseer-Ibn-Azkar

03 February 2016 0 10K Report

For example, if I want to run it for continental North American scale with 36km, 12km, and 4km grid resolution, what would be the minimum and optimal hardware requirement for a day/a week simulation (considering reasonable time)? Thanks for any information!

Badges
Science topic

More Muntaseer Ibn Azkar's questions See All

What is the ideal time to administer prophylactic antibiotics to cancer patients after anticancer therapy?

I need clarification on the appropriate timing for administering prophylactic antibiotics to cancer patients.

29 April 2024 7,106 2 View

Can boron or borophene be deposit on alumina through VLS method ??

Want to deposit borophene on Alumina

19 June 2023 3,858 0 View

I have a protein structure with 2.8º, R free is still 0.3720. How can I decrease this? I have added possible ligands in unmodelled blobs but no luck?

Protein

03 April 2023 7,308 0 View

Is it possible to determine the weight and height of a person from his palm image (Using Computer Vision)?

I've read a couple of literature papers on How to determine the height/weight of a person using face Images. Thus, using computer vision/CNN Below are some of the literature papers. 1: Show me...

10 August 2022 1,530 1 View

How to determine the polarization sheet charge of AlGaN/GaN quantum well from the measured electric field in this structure?

how to determine the polarization sheet charge of AlGaN/GaN quantum well from the measured electric field in this structure?

23 March 2021 6,509 2 View

What do you think are the most relevant policy options for African governments post COVID 19?

Despite the low recorded cases, African countries are projected to be the most hit by this pandemic. The continent's already fragile nature in terms of economic growth, development, and well-being...

24 May 2020 6,492 13 View

What is the thickest Photo-resist you have ever used and / heard of ?

We know that, any particular PR can give a range of thicknesses depending on spin speed. However, this also means that there is an upper bound of thickness for each of them. Sometimes we use...

15 April 2020 2,566 0 View

Purification of Octapeptin C4?

I am doing synthesis of Octapeptin C4 analogues with variable tail moieties as part of my project. I have made the final compound, which is cyclized and all BOCs removed. The problem is, I can't...

16 December 2019 1,994 2 View

Is there a way to live-stain the nuclei in the early zebrafish embryo?

I would like to image the nuclei of the zebrafish embryo for the first 5-6 hours of development, ideally from 4- or 8-cell onwards. I have searched the literature but aside from injecting sytox...

20 August 2019 7,570 4 View

How can I draw calibration curve for a gas chromatograph with known standards??

I am trying to calibrate a GC in my lab and I am completely new at using one. I have ran a cylinder of known concentrations (100 ppm) of Acetaldehyde, Acrolein, Propylene Oxide, Propanal and...

08 June 2019 3,439 10 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View