What is the lifespan of male Wister rats after being treated with streptozotocin to induce diabetes?

More Syed Ilyas Shehnaz's questions See All

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

SSR primers are species specific or we can use it for any plant species ?

Hi, any one please guide me; SSR primers are species specific or trait specific. i have few primer which was reported in articles for wheat yield can i use these similar primer for lentil yield...

20 February 2021 315 4 View

How is Initial GDP measured ?

Dear All, I am working on estimating Debt-Growth Threshold but confused about some points. My questions are; - How do we calculate initial GDP Per Capita? Shall we do it in STATA or excel file?...

15 February 2021 2,677 2 View

How to get actual or true SoC while predicting SoC for Batteries using Data Driven Approaches?

I have seen it in multiple research articles that authors use certain approaches to predict electric vehicle battery's state of charge(SoC) and then they compare it with battery's true SoC. So I...

11 February 2021 9,070 3 View

How fishery by-products/fish waste can be utilised as efficiently, cost-effectively and eco-friendly?

Fishery by-products utilisation in the industry with minimum cost and low carbon emissions.

29 December 2020 1,752 11 View

Techniques of Machine/Deep Learning for Battery's SoC Estimation?

Hi everyone I want to know which techniques of Machine Learning/Deep Learning I can use for more accurate SOC estimation of Lithium Ion batteries. Thanks and Regards

24 December 2020 2,096 1 View

How can I know which sequence is the correct one if there are lot of predicted sequence in database for my target gene?

Right now, I want to design qPCR primer for my target gene. But that gene has 21 predicted mRNA sequence in the NCBI database. Most of the sequence names are same but only different location...

23 December 2020 5,531 12 View

How to rectify the miscomputation of Pressure and Continuity in HVAC CFD Simulation Using OpenFOAM?

I'm using OpenFOAM to run a CFD study of thermal comfort within a hall. I'm using OpenFOAM v1912 and BouyantBoussinesq(Simple&Pimple)Foam solver. eI have 6 inlets and outlets each with specific...

21 December 2020 1,303 3 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

How can we add reinforced thermoplastics with granules in injection molding machine?

I need to make an injection molding machine in which short fibers are to be introduced. Short fiber length and material properties are to be determined and also the material strength are to be...

22 February 2021 4,290 1 View

Will rat colon cancer cells (DHD/K12) derived from BDIX rats grow in Sprague Dawley ?

we plan to induce colon cancer by injection. Cell lines derive from BDIX rats, but our experimental setting would favour SD rats. any experience?

23 January 2021 1,437 2 View

Is there a study on the maximum thumb extension that can be possible in a range of population while using injectors?

In Most pen injectors while dialing the dose, the dose dialer comes our or extends outside the pen as dialing happens. How much maximum extension of dialer is acceptable for performing...

17 January 2021 9,770 1 View

How to couple Moldex 3D with MATLAB for design optimization of an injection mould?

Hello, I would like to use the software Moldex 3D for the design optimization of an injection mould. How can I couple Moldex 3D with a MATLAB code? Any help appreciated, I wish you all a happy...

09 January 2021 569 2 View

How to setup ANSYS Fluent for simulating the filling stage of an injection mould?

Hello, I am using ANSYS Fluent for simulating the filling stage of an injection mould. However, when comparing the results with those of specialized software, such as Moldex 3D, I found the...

07 January 2021 7,992 1 View

Do drugs that are injected i.t in rats reach the supraspinal system and how long does it take to clear them from spinal cord?

I am injecting intrathecally (between L5-L6) , in rats, cannabinoid analgesics and I was wondering if they can reach the brain and have effects there as well ? Also I need to pretreat with...

07 January 2021 5,397 4 View

How big the Balb/c mice spleen after immunization?

I am working with Balb/c mice, and in my experiment, I have to inject mice with antigens, then get their spleen and collect the splenocytes for fusion. Recently, I get into trouble with the mouse...

04 January 2021 3,591 3 View

How can I reduce the viscosity of corn oil used as vehicle for administration in animal experiments?

Dear all, I am using corn oil as vehicle for subcutaneous injection and I want to reduce the viscosity of the vehicle (corn oil) to enhance the delivery of the main compound of interest....

18 December 2020 1,773 6 View

Could someone please help me in Parallelization of following UDF in Ansys fluent?

I was able set UDF for my dynamic mesh using following UDF. It works in serial mode. Now problem is that I want to speed up my solution, so parallelization is needed. I have gone through the user...

17 December 2020 420 4 View