What is the difference between ELASE and ALLAE?

07 July 2018 0 9K Report

When studying the energy output in my model I find ELASE which is the total artificial strain energy in the element, and ALLAE, which is the articial strain energy too, what difference is there between those two outputs? If I what to make an hourglass study, which should I look at?

Badges
Science topic

More Ana Walsh López's questions See All

What system or material can I use to properly embed an end of a cantilever beam?

I am studying vibrations in a cantilevered beam. I need this beam to be totally embeded but the results I am getting are not logical. I think this is because the system where it is embeded doesnt...

02 March 2019 4,785 3 View

How to calculate damping factors for different vibration modes?

I am currently studying the behaviour of a cantilever beam and I need to obtain the damping factor of each mode of the beam. Does anybody know how to do this? I have the time-response of my beam...

31 December 2018 7,616 6 View

How can I put an initial amplitude to a beam in Abaqus explicit?

I would like to indicate the initial position of the end of my beam so I can let go afterwards and see it's time response. Since I only have the amplitud it must have at t=0, I cant use a tabular...

11 December 2018 2,842 3 View

In abaqus, in order to analyse the plastic dissipation at the end of a crack, do I need to specify the plastic behaviour of my material?

I'm studying the effects of plastic dissipation in cracks growth, but when I plot ALLPD in the visualization module it's constant at 0. I guess it's because I didn't specify any values in plastic...

05 June 2018 1,779 3 View

How can I analyse using Abaqus the energy dissipated in the crack of a beam?

I am studying the energy balance in a recessed beam which contains a crack. I need to calculate the energy dissipated in that crack, which outputs can I use? I have used a set containing the...

05 June 2018 4,710 3 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

What are some of the research gaps in machine learning and artificial intelligence in africa?

i would to know some of the research gaps in the artificial intelligence field in most african countries.

03 March 2021 6,145 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View