How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

No title

03 March 2021 5,360 2 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

The procedure compute?

02 March 2021 5,204 3 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

22 February 2021 5,408 1 View