What is the best filter size we can use in our solvents for LC-MS/MS ?

16 October 2013 1 5K Report

LC-MS/MS system consisted of the 460-LC auto samplers, 212-HPLC Chromatograph Pumps. Solvents are water and methanol + 0.1 % formic acid.

Vítor Spínola

For HPLC 0.45 um and UHPLC 0.22 um.

Badges
Science topic

More Aysana Sadra's questions See All

Is ANSYS Fluent good for simulation of a three phase reactor(stusy of its hydrodynamics or mass transfer...)?

Hello everybody, I would like to simulate a three phase reactor and study its hydrodynamics. I would like to know which type of software is better? I have a good command of ANSYS Fluent and I am...

10 February 2021 4,303 3 View

How to compare different concentrations of nanoparticles for characterization from ICP-MS?

I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...

02 March 2021 7,626 1 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

I want to performe MALDI-TOF MS for bacterial identification, I would appreciate it if anyone can tell me the matrix solution preparation protocol ?

based on what I've studied on multiple papers, for peptide and protein identification Alpha-cyano-4-hydroxycinnamic acid (CHCA) is an appropriate matrix to use, I also know that the CHCA powder...

26 February 2021 6,799 3 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Why ICP-MS test for Teflon filters that collected PM2.5, show really high results in the millions of ug/g ?

I analyzed soil and ash samples using ICP-MS for 28 metals, then I resuspended those samples to collect PM2.5 particles in a filter using a selective inlet inlet. My only issue that Fe and Al...

13 February 2021 7,592 3 View

What influences inter-day reproducibility in UPLC-MS/MS analysis?

I was analyzing some metabolites in human plasma. While the intraday precision of these metabolites was acceptable ( less than 20%), the interday precision was quite large. So what influences...

13 February 2021 9,183 9 View

How do I prepare and store insect samples for JH measurements?

I need to preserve termite samples for future quantification of juvenile hormone in their bodies. Or extract the Juvenile Hormone and keep that samples stored for future quantification. I may need...

09 February 2021 1,995 1 View

MS/MS protein analysis?

Hi Everyone: I want to quantify the relative amount of a protein in 2 samples. I will first digest the sample with trypsin, and subject the resulting peptides to LC-MS/MS analysis. I will then...

25 January 2021 8,333 3 View

2.6 Drying gas flow controller cannot regulate the requested setting after a fixed amount of time?

We keep getting this error on our Agilent 6470 TQ. We were told it could either be our N2 generator or filter traps. We've called the manufacturer of our generator and they believe it's working...

21 January 2021 2,969 1 View

How to distinguish pure and adulterated honey using NMR spectroscopy?

What are the common adulterants in commercial honey? how to identify pure honey and adulterated honey with the help of NMR spectroscopy? Is there any other technique to check purity of honey?

20 January 2021 5,456 12 View