What is meant by Hydrostatic acceleration in ANSYS software ?

Sangamreddi Chandramouli @Sangamreddi_Chandramouli

02 February 2018 0 2K Report

We are modelling a Reinforce concrete water tank in ansys.

While modelling it is asking Hydrostatic acceleration. So we would like to know the meaning of this.

Badges
Science topic

More Sangamreddi Chandramouli's questions See All

How to find a good/genuine journal to publish?

These days, finding a good journal to publish work is the most difficult thing. So many researchers are not finding the way to publish their works. so in view of this, how to find a journal which...

07 August 2019 2,609 5 View

Can anybodu suggest a good journal to publish the work on "STEEL TRUSS OPTIMIZATION USING GENETIC ALGORITHMS AND 2D TRUSS ANALYSIS PROGRAM IN MATLAB"?

We have done a work on "STEEL TRUSS OPTIMIZATION USING GENETIC ALGORITHMS AND 2D TRUSS ANALYSIS PROGRAM IN MATLAB". We would like to publish it. So we need good journal to publish the work.

02 March 2018 8,006 2 View

What are the various methods of finding the reliability of water supply pipe network?

I am working on finding the overall network reliability of a municipal water supply pipe networks. So, i would like to know all the methods available in the literature.

01 February 2018 4,418 8 View

Why Artificial Recharge of groundwater?

I am teaching the course on Groundwater Development and Mangagment. In that course, one unit is on Artificial Recharge of groundwater. In this regard, I want to know Why Artificial Recharge of...

01 February 2018 3,518 6 View

Can anyone suggest the best journal for publishing work on water auditing?

We carried out a project on water auditing : a case study of Vizianagaram town". We would like to publish it. So please suggest the best journal.

01 February 2018 1,475 2 View

Can anybody tell about maximum dosage of superplasticiser in pervious concrete?

We are working on previous concrete for increasing in strength without compromising the permeability. So in-view of this , we would like to use super plasticisers in pervious concrete.

11 December 2017 5,104 3 View

Can anybody explain how to find the permeability of pervious concrete experimentally?

We are working on a project for studying the characteristics of pervious concrete. We are planning for fabrication of a model for finding the permeability of pervious concrete.

10 November 2017 3,627 8 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View