Can anybodu suggest a good journal to publish the work on "STEEL TRUSS OPTIMIZATION USING GENETIC ALGORITHMS AND 2D TRUSS ANALYSIS PROGRAM IN MATLAB"?

More Sangamreddi Chandramouli's questions See All

How to find a good/genuine journal to publish?

These days, finding a good journal to publish work is the most difficult thing. So many researchers are not finding the way to publish their works. so in view of this, how to find a journal which...

07 August 2019 2,609 5 View

What is meant by Hydrostatic acceleration in ANSYS software ?

We are modelling a Reinforce concrete water tank in ansys. While modelling it is asking Hydrostatic acceleration. So we would like to know the meaning of this.

01 February 2018 2,210 0 View

What are the various methods of finding the reliability of water supply pipe network?

I am working on finding the overall network reliability of a municipal water supply pipe networks. So, i would like to know all the methods available in the literature.

01 February 2018 4,418 8 View

Why Artificial Recharge of groundwater?

I am teaching the course on Groundwater Development and Mangagment. In that course, one unit is on Artificial Recharge of groundwater. In this regard, I want to know Why Artificial Recharge of...

01 February 2018 3,518 6 View

Can anyone suggest the best journal for publishing work on water auditing?

We carried out a project on water auditing : a case study of Vizianagaram town". We would like to publish it. So please suggest the best journal.

01 February 2018 1,475 2 View

Can anybody tell about maximum dosage of superplasticiser in pervious concrete?

We are working on previous concrete for increasing in strength without compromising the permeability. So in-view of this , we would like to use super plasticisers in pervious concrete.

11 December 2017 5,104 3 View

Can anybody explain how to find the permeability of pervious concrete experimentally?

We are working on a project for studying the characteristics of pervious concrete. We are planning for fabrication of a model for finding the permeability of pervious concrete.

10 November 2017 3,627 8 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

What degree of missing data in a particular case/participant results in Expectation-Maximisation no longer working?

I'm dealing with a mediation model and am using the PROCESS module in SPSS. Due to SPSS and PROCESS being limited in the imputation methods - being unable to handle multiple imputation - the other...

02 March 2021 4,362 1 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

How to add a journal?

I would like to know how to register the journal Flora Montiberica (ISSN 1138-5952 - eISSN 1988-799X) in Research Gate.

02 March 2021 8,156 2 View

Can NFL theorem be valid in infinite search space in ML?

NFL theorem is valid for algorithms training in fixed training set. However, the general characteristic of algorithms in expanded or open dataset has not been proved yet. Could you show your...

01 March 2021 1,189 3 View

Is it possible to remove a preprint posted by a journal which is already rejected?

As we know many journals are posting preprints (DOI) in advance before the peer-review process. However, there is no guarantee that the preprints get published. The journal's reviewers undergo the...

01 March 2021 5,778 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

Muhammed Abbas Husain

Please follow this link and choose the appropriate journal for your work.

http://www.scimagojr.com/journalrank.php?area=2200&category=2205

Best regards.

Gilberto Thiago de Paula Costa

You can try this:

Advanced Steel Construction - http://ascjournal.com/

International Journal of Solid and Structures - https://www.journals.elsevier.com/international-journal-of-solids-and-structures/