What causes a magnetic contactor burnt?

MC12059 ChungKarYee @Mc12059_Chungkaryee

02 February 2017 0 3K Report

Good day everyone,

Is anyone knows why a contactor burnt ?

It is a 220V and 50Hz magnetic contactor which connected with the oil circulation pump motor.

thank you.

Badges
Science topic

More MC12059 ChungKarYee's questions See All

How to calculate the flow rate of water inside the piping using pressure?

Pressure is 2 bar and the pipe diameter is 2 inches

11 December 2017 6,930 5 View

What is the application for paper gasket?

Good day everyone! Is it suitable to use paper gasket for the thermal oil valve?

11 December 2016 5,539 1 View

What is VPN?

I have learned from website which said that I can change my IP address through VPN but I don't understand what is it and also is it safe ?

10 November 2016 8,368 2 View

Does anyone know in what condition we need to tune the sensitivity adjuster of the sensor? Is it based on the size/diameter of the target?

Good day everyone, Sensor Model: Omron E3Z-T61 photoelectric sensor. The attachment below is the manual and image of the sensor. Thank you in advance.

10 November 2016 7,890 2 View

Hi, what to do if error message always appear when running simulation using ANSYS fluent?

Currently running simulation using ANSYS fluent with time step size = 0.01 and number of time steps = 360000. (In reality i have to carry out the process in 1 hour, so 360000 times 0.01 equal...

04 May 2016 4,223 3 View

Hi, anyone know how to restore the license file to default format?

Hi, i not carefully open the license file in notepad and i can't find a way to restore it into default format. I have try use the 'regedit' method but still the icon still is in notepad form. Does...

02 March 2016 4,559 0 View

Anyone know how to create 2D using Autodesk Simulation CFD 2015?

Hi good day to everyone. Recently i'm trying to construct a 2D model using Autodesk Simulation CFD but i failed so i wish to get some guidelines from you all on how to create the 2D model in...

02 March 2016 5,192 5 View

Anyone know how much power(watt) of electrical heater that will be required to generate heat which can achieve 400 degree Celsius?

Hi, currently i try to figure out what kind of heat sources that can be used to heat the plastic to 400 degree Celsius and the amount of power(watt) that needed to consume in order to reach and...

01 February 2016 2,962 4 View

Hi, anyone know what is the factor of safety of mild steel?

AISI 1018 mild/low carbon steel has excellent weldability and produces a uniform and harder case and it is considered as the best steel for carburized parts. AISI 1018 mild/low carbon steel offers...

10 November 2015 7,788 3 View

What kind of bearing is suitable to support applied load of 1000 lbs ? Is there any other factors that we need to consider when selecting a bearing?

Hi everyone, the provided link is some information related to the bearing.

09 October 2015 9,594 7 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

An animal in not a rock (e.g., Koch 2013), it has an internal constitution that can be modified?

Vertebrates and invertebrates (e.g., arthropods: insects, crustaceans, etc.) have two different neuro-muscular systems given their differential construction: the former have an endoskeleton and...

07 August 2024 648 0 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

How can major oxides determined by ICP-MS/ES be normalized to 100% volatile free? How does this connect with LOI?

I am analyzing cherts from different sources found within one specific geologic formation using ICP-MS/ES. My committee was asking this question about my analysis. I was not sure how to answer this

05 August 2024 7,902 3 View

Do you think can be any gas and oil bearing rocks in Eastern part of Iran?

I want to know more about petroleum deposits in Iran.

02 August 2024 8,725 3 View

How do environmental toxins interact with genetic predispositions to increase cancer risk?

I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from experts in the field. If you are an expert or researcher working on...

02 August 2024 2,627 1 View

Difficulty with permittivitt and Magnetic Permeability Calculations?

Difficulty with permittivitt and Magnetic Permeability Calculations Hello everyone, I have all the parameters related to the calculations of the permittivitty and magnetic permeability...

30 July 2024 5,206 1 View

Heavy Crude oil PVT Data?

Hello i need heavy oil PVT data having viscoisty of 2000-3000 cP. If someone have it or research papers about it, kindly share it with me Thanks

25 July 2024 6,940 1 View

What are the most PROBLEMS of HYBRID nanofluid in oil industry ?

explain your idea

23 July 2024 1,197 0 View

I am working on III-V based tandem solar cells.Can anyone explain that solar cells work under forward or reverse biased conditions?

I want to know that n-doped side of solar cell is connected with positive or negative electrode.

20 July 2024 1,348 2 View